Recent content by TommyGuns

  1. TommyGuns

    Pro Flo 4 with Delphi FE0114 or ACDelco EP381

    Attached is a corrected wiring diagram. The previous one would short circuit whenever the left tank was selected. Circuit numbers, wire colors and gauges are all based on the 1983 truck wiring manual. Circuits 53R and 54R (relay) are a larger gauge of wire which must replace the wiring...
  2. TommyGuns

    Pro Flo 4 with Delphi FE0114 or ACDelco EP381

    With some googling I came up with the attached wiring design. It looks good to me, but I'd appreciate a sanity check from y'all before I start wiring it up. My goal is to retain my dual tanks without adding any more switches in the cab. Plus the wiring design is similar to the TBI dual tank...
  3. TommyGuns

    Pro Flo 4 with Delphi FE0114 or ACDelco EP381

    This is the main reason why I am converting the fuel system now. The fuel sump.. It was great for getting the truck driving semi-reliably. But it would randomly shut off. The random shut off would be after driving for a while (30 - 45 mins) and immediately after I let off the throttle to coast...
  4. TommyGuns

    Pro Flo 4 with Delphi FE0114 or ACDelco EP381

    I'm definitely looking at Walbro, Aeromotive as well. I was leaning toward Delphi and AC Delco due to their history with GM, but my number one concern is reliability and drivability. I did look around where I live and a Dyno / ECU tune is less expensive than I thought. I may end up making an...
  5. TommyGuns

    Pro Flo 4 with Delphi FE0114 or ACDelco EP381

    Perhaps I'm confused. The injectors I have are 29 lb/hr, 58 PSI injectors. If I want to run 29 lb/hr at 43 PSI, wouldn't I need to change to injectors rated for 29 lb/hr at 43 PSI? I'll give the tech line a call for sure once they open again.
  6. TommyGuns

    Pro Flo 4 with Delphi FE0114 or ACDelco EP381

    Right, and the fuel sump I'm using has a built in vacuum adjusted fuel pressure regulator. Part of the installation instructions are to run the sump without vacuum and ensure it's set to 58psi. Then you connect the vacuum line to one of the ports on the intake, and at idle you'll see lower...
  7. TommyGuns

    Pro Flo 4 with Delphi FE0114 or ACDelco EP381

    For clarity, this is the kit that is installed on my truck: https://www.edelbrock.com/edelbrock-pro-flo-4-efi-kit-35780-for-sb-chevy-with-vortec-e-tec-cyl-heads-35780.html It includes 29lb, 58 PSI injectors. I just noticed that according to their product page, this kit is rated for up to 450...
  8. TommyGuns

    Pro Flo 4 with Delphi FE0114 or ACDelco EP381

    No idea. I didn't build the motor and I haven't had it on a dyno. Putting it on a dyno wasn't on my to-do list for the truck. Apart from the Vortec heads and a mild cam, the motor isn't built. It runs on regular gas without detonation, so the compression is close to factory. My guess would be...
  9. TommyGuns

    Pro Flo 4 with Delphi FE0114 or ACDelco EP381

    Even if I go with the EP381, that pump is rated less than the "required" flow rate of 57 GPH per the Edelbrock Pro Flo 4 instructions. I daily drive my square, so I converted to EFI for reliability and drivability. I sometimes have to leave for work for months at a time, so I need the truck to...
  10. TommyGuns

    Pro Flo 4 with Delphi FE0114 or ACDelco EP381

    I was actually looking at the Delphi FE0114, since it is more available. I had the same experience trying to find an EP381.
  11. TommyGuns

    Pro Flo 4 with Delphi FE0114 or ACDelco EP381

    I have seen several posts here where people used the Delphi FE0114 or ACDelco EP381 fuel pumps with the Pro Flo 4 system for a SBC. According to the Pro Flo 4 instructions the EFI system requires a minimum flow rate of 57 GPH. However, the FE0114 is rated at 32 GPH, and the EP381 is rated at 41...
  12. TommyGuns

    A/C but no heat

    Laqota is 100% correct. I was googling and searching, trying to figure out the OEM configuration for reconnecting my 1983 HVAC vacuum controls to the engine (a PO never reconnected it). I was thinking what good would a vacuum reservoir be if there was no check valve between it and the engine...
  13. TommyGuns

    Air Cleaner Fitting - PCV?

    Thank you all, looks like this part is called an "Air Cleaner Deflector" and is available as new old stock: https://www.ebay.com/itm/175692996083
  14. TommyGuns

    Air Cleaner Fitting - PCV?

    I was thinking it was some kind of return from the crankcase, because it has a baffle directly in the path of the air being returned to the air cleaner. The unknown part belongs on the driver side. The cutout in the air cleaner for this mystery part has a "D" shape. The factory PCV filter is on...
  15. TommyGuns

    Air Cleaner Fitting - PCV?

    Another closer shot of the part that might be helpful. Thanks in advance to anyone who can help me identify it.
See more

Latest posts

Forum statistics

Threads
45,570
Posts
986,596
Members
38,662
Latest member
imyourhuckberry
Top