Recent content by sqhead

  1. S

    Which motor mounts work for my truck?

    Looking for a good set of motor mounts (rubber) inserts for my 383 stroker to 85 Chevy k10. I’d like to find ac delco but it shows up not for my truck on summit. Anyone know part numbers or good brands that will work? I also need the bracket that goes on engine also. Thanks.
  2. S

    Are SM465 cases interchangeable

    I have an 85 Chevy k10 with SM465 and was told that the countersafts came in 2 size on the input side 1.3” or 1.4” for later years. Mine is 1.4”. I’m looking to get another case to swap all my parts into and found one out if 78 k10 but don’t know if the counter shaft is different size or if it...
  3. S

    Hole in sm465 casing?

    On the top of my SM465 case it has a small pin hole. I’m assuming that’s just wore over time. It’s where the stud on top fork cover goes in. Looking for opinions on if it will leak. Couldn’t tell if it leaked before because entire thing was covered in oil.
  4. S

    Need to find bump stops

    I should have put some more details. Thanks for pointing that out. It would be daily driving. No off-roading. 3” lift. And I’m just talking about the hard rubber bump stops and not the actual shock looking bump stops.
  5. S

    Need to find bump stops

    I’m looking at putting new bump stops on front and rear of 85 Chevy k10, but mine doesn’t have any on it now. So, question is Wjat is a good size or recommendation of brand/style to get for front and rear? I see different types and just curious if anything special to pay attention to. Thanks
  6. S

    More gear pattern pic. This time it’s for my rear set

    These are a new set of gears and carrier
  7. S

    More gear pattern pic. This time it’s for my rear set

    Just sloppy when I applied. Never meant for it to be on there
  8. S

    More gear pattern pic. This time it’s for my rear set

    Looking for some advice. I finished up on my front. Now I’m on to my rear set of gears. Please let me know your thoughts on the gear pattern. It’s a GM 10-bolt 8.5” with backlash at 8. Thanks
  9. S

    Gear pattern pics. Need some input?

    Copy on a little to deep. Any idea on amount if adjustments
  10. S

    Gear pattern pics. Need some input?

    I’m have my front diff set up with a pair of set up bearings I made up. It’s a 10-bolt 8.5”. I have the backlash at .007. Please take a look at my gear pattern and give me your thoughts or recommendations. Thanks
  11. S

    Sm465 rebuild kit

    Thanks for the info.
  12. S

    Sm465 rebuild kit

    Rebuilding a SM465 transmission. What is the best rebuild kit out there? Anyone have or heard experience with some better than other? Thanks
  13. S

    Drivers side firewall?

    I’m smoothing firewall on 85 Chevy k10. Question is on drivers side the bottom part has a lip that runs from center to middle of the drivers side panel. Has anyone removed that bottom lip on drivers side that is bumper out and just straighten across the lip down but not bumped out? The passenger...
  14. S

    Wiring harness advice pertaining to bulkhead and smoothing firewall

    I’m looking at American auto wire and painless kits for complete rewire of truck. I liked the idea of getting the kit that is just for the truck for easy layout, but they have the original bulkhead also. I am trying to smooth the firewall and don’t want the bulk head. Any advice if someone has...
  15. S

    3/16” brake line to rear?

    Copy on that. That’s some good info. Thanks
See more

Latest posts

Forum statistics

Threads
42,249
Posts
912,064
Members
33,749
Latest member
630erik1
Top