Recent content by rt66paul

  1. rt66paul

    1986 C10- Is it reliable enough for a daily driver?

    I drove a '54 pickup for 4 years, it was 20-24 years old. It ran well every day - that is back when vehicles did not usually last 80k mi.
  2. rt66paul

    Header back exhaust fitment for C20 454

    How much difference does the 3" crossover with 3" tubes all the way back vs a 3" equalizer tube really make? I remember adding a 2nd pipe and muffler for dual exhaust on 1 7/8", 2" and 2 1/2" pipe making a huge difference. I suspect that on an engine with less than a 400 HP capacity, the...
  3. rt66paul

    4:10 Gear swap?

    Set it up for a period 5th wheel trailer and use it as intended.
  4. rt66paul

    I learn something every day, but not today....

    A few states require Ca standards on the new vehicle sold in state.
  5. rt66paul

    Best Choice for Drivetrain

    RV cams are replacement cams for otherwise stock engines. They have more grunt(torque) at the low end - they have a flatter torque line through out. They are not designed to go over 5000 rpm(neither are stock engines). These give you the power you need without the smog requirements. They do NOT...
  6. rt66paul

    1 Ton with a 10' foot bed

    The Longhorn had an extra 6" added to an 8' bed. There was room to add a custom gas tank in front of a standard camper - they all were wooden floor beds - not 10' long
  7. rt66paul

    Please help me make a decision

    I would think that a K20 would have a TH400, but maybe the 4wds did not. The 400 is stronger than a 350, but they are strong and do not cost a months pay to overhaul. These vehicles are not known for their great gas mileage, there is little you can do(other than keep your foot out of it) to help...
  8. rt66paul

    How to pick the correct headers...

    How about using Rams Horns? They fit, are easy to hook up and don't get in the way. Unless you are expecting 6500 rpm, I wouldn't overthink it.
  9. rt66paul

    Can you make a 305 stroker with 350 crank and rods?

    I remember using a steel 283 crank and putting in in a 327(back in the day) We called it a 301. Popup pistons 11 1/2 to 1 with double hump heads. That would get a bucket T, a shoebox or an early Nova to scoot. The Z28 302 was the same idea, with 4 bolt mains or the special racing mains, but you...
  10. rt66paul

    Old school Maglite / Magcharger flashlight and installation

    Will it fit on the left side windshield post? You could pull the wiring through the dash.
  11. rt66paul

    1991 GMC Suburban Overland build Question(s),

    I considered putting on a roof rack on mine and in looking it over, I came to the conclusion that maybe to best mount point would be to drill holes through the side pillars near the shoulder harness mounts, bend some 3/16 stock and cut and/or weld to fit. If you want a big rack, there are 3...
  12. rt66paul

    Is there any hope for these tools?

    https://www.familyhandyman.com/project/how-to-remove-rust-with-electrolysis
  13. rt66paul

    Intake is Outgoing

    You have a 1 ton, so you might be able to get away with a lot more than others. The standards in the 70s and 80s were different in Ca those years, some on trucks that had the same equiptment. You truck was obviously used(and probably purchased as a trailering special), so you have to go with...
  14. rt66paul

    California Square Body fans - Proposal to extend smog exemption model years

    It would be a lot cheaper to just put the parts back. Ca smog laws are a nightmare for anyone who prefers older vehicles. Believe me, they want to get 3/4 and 1 ton trucks and SUVs off the road ASAP.
  15. rt66paul

    I-Talian Tune UP

    We used to say blowing the spiders out by opening up the secondaries on the 4 barrel carb(like no one did driving around town). Where does Marvel Mystery Oil come in here? I remember dumping a can in and soaking the top end for a couple of days - bringing back an old junk yard I6.
Top