Recent content by proddy2008
-
P
Static drop for those on an xtreme budget...
:popcorn:- proddy2008
- Post #64
- Forum: Lowered & Street Systems
-
P
front steering/ suspension
Will do I gues I just cranked down on it a little too tight lol thx for the advice- proddy2008
- Post #17
- Forum: Lowered & Street Systems
-
P
front steering/ suspension
oh so EVERYTHING is brand new now from tie rod to tie rod wvery dam piece i kept the steering box but everything else is 100% brand spankin new on the front end.... and heres the problem... drove it home today after alignment and everything was tooooo tight even a minimal imput on the steering...- proddy2008
- Post #15
- Forum: Lowered & Street Systems
-
P
tbi to carb?
Iv heard very good things about those vortec heads, I heard they came out with a carb manifold for them to and iv been considering a set for.my next motor aswell I dont know/havent heard how they hold up under boost so I am a little worried I cant recall how they do with porting either lol but...- proddy2008
- Post #18
- Forum: Carb Fuel Systems
-
P
Factory oil cooler?
yep iv got one too, if ya want to get it workin again or want any one part for it oreily sells the whole kitfor 150 lol basteges wont part it out for ya- proddy2008
- Post #5
- Forum: Engine & Performance
-
P
Oil Leak Pissing Me Off
mine seal good they just have a hole in the front iv got sealed with the jb putty if you come to houston il give em to ya lol not pretty but like i said they work fine- proddy2008
- Post #10
- Forum: Engine & Performance
-
P
Stock Gauges
dam c4 ya beet my to it lol. oh well im still lookin if anybody runs across some drop me a line i want to get them before i do my new wiring harness- proddy2008
- Post #20
- Forum: For Sale
-
P
front steering/ suspension
sooooo went to replace my balljoints..... yep i now have completely new everything underneath exept the crossmember and the uper control arms lol. something to keep in mind if/when i ever buy annother truck..... people on farms are not nice to their suspension lol came in at under 500 for...- proddy2008
- Post #14
- Forum: Lowered & Street Systems
-
P
Garage And Shop Safety
lol HE did i grabed a fire extinguisher and said dont do it man! kids these days just dont listen- proddy2008
- Post #72
- Forum: Garage
-
P
tbi to carb?
i dont know if youve done this yet but as far as the throtle cable brackets and such, iv always had trouble with them lol, you could go to the junk yard and just grab the manifold carb and dizzy for probobly less than a $100 bill... or wait do you have the centerbolt or perrimiter bolt heads?- proddy2008
- Post #16
- Forum: Carb Fuel Systems
-
P
What's the most dangerous tool in your shop?
im covered in beeeez!- proddy2008
- Post #42
- Forum: Garage
-
P
i cant drive 55!
lol ok this one is going on the back burner right now i found annother mod i can do to be able to keep up with trafic.....and it lasts 200000 miles lol yep going with super singles the extra 10 inches in diameter is like od! of course i know that this has the obvious draw back of bigger heavier...- proddy2008
- Post #10
- Forum: Transmission & Transfer Case
-
P
Garage And Shop Safety
yep crispy=good on chicken not so good on you- proddy2008
- Post #68
- Forum: Garage
-
P
What's the most dangerous tool in your shop?
funny the tools get me waaayyyyy less than me being lazy and leaving sharp edges when im building brakets... iv realy gotta stop that lol- proddy2008
- Post #38
- Forum: Garage
