Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
peats's latest activity
P
peats
reacted to
Grit dog's post
in the thread
What wire under new carpet?
with
Like
.
Well I was gonna walk you though a couple scenarios since you’re obviously clueless and didn’t even provide enough info to answer...
May 25, 2026
P
peats
reacted to
Ricko1966's post
in the thread
What wire under new carpet?
with
Like
.
You know asking the guy who's going to install it is the best advice you could get. I've done lots of prewires,one person wants...
May 25, 2026
P
peats
reacted to
Rustisbest's post
in the thread
What wire under new carpet?
with
Like
.
May 25, 2026
P
peats
reacted to
idahovette's post
in the thread
What wire under new carpet?
with
Like
.
So what would be wrong with asking the guy who is goanna put it in???????????.......he SHOULD have some input on it......oh and EFF you...
May 25, 2026
P
peats
reacted to
Ricko1966's post
in the thread
Detent/Kickdown cable
with
Like
.
If you are using let's say a 1979 c10 350,and using the carburetor and brackets for a 1979 engine. I'd buy one for a 1979 c10 Chevrolet...
May 11, 2026
P
peats
replied to the thread
Engine Build
.
I use a stock starter but wrap the hedder in the area of the starter.
May 11, 2026
P
peats
reacted to
Ricko1966's post
in the thread
Battery to body ground
with
Like
.
Yes ground it to the core support. For our purposes no,I don't think you can have too many grounds.
May 11, 2026
P
peats
replied to the thread
87' 350 SBC Rebuild
.
I'm confused as to why you would want to put electric fans on a mostly stock build. A good radiator and fan clutch setup should be...
May 11, 2026
P
peats
reacted to
legend57's post
in the thread
87' 350 SBC Rebuild
with
Like
.
In '87, the bottom end was good and stout with the 4-bolt caps. The top end was terrible, mostly for smog reasons and economy. The...
May 11, 2026
P
peats
reacted to
Sad Sack's post
in the thread
Fuel Smell
with
Like
.
Jus' thowin it out there, charcoal cannister?
May 11, 2026
P
peats
reacted to
TotalyHucked's post
in the thread
Forbidden Fuel Experiment: E85 In a Mostly Stock Square
with
Like
.
I'm curious, why? Just as an experiment? At least you're in corn country where it's usually as cheap as or cheaper than regular. It's...
May 11, 2026
P
peats
reacted to
75gmck25's post
in the thread
Cam shaft
with
Like
.
You said you are “building” a 350, so does that mean you are replacing pistons or making other changes that would increase compression...
May 11, 2026
P
peats
reacted to
Ricko1966's post
in the thread
Cam shaft
with
Like
.
You need to check the head casting numbers. I'd bet you need heads too,if it's on the 81 in your first post. Probably 624 castings,low...
May 11, 2026
P
peats
reacted to
Goldie Driver's post
in the thread
Tire size or possible lift recommendations for the 79’ K30
with
Like
.
My 60 year old opinion :rofl: is it has a good stance now and adding a lift will be dollars, labor, and possibly driveshaft issues for...
May 11, 2026
P
peats
reacted to
Ricko1966's post
in the thread
E85 conversions considering gas prices
with
Like
.
E85 especially on our trucks is not a good economic move. Alcohol attracts water which destroys carbs,and rusts tanks,as well as settles...
May 11, 2026
Latest posts
SoCal
Latest: Shorty81
Today at 6:07 AM
Introduction
LWB driveshaft question
Latest: xm20k
Today at 5:56 AM
Differential & Driveline
Grounding question
Latest: DatKat933
Today at 3:42 AM
Electrical & Audio
Is this a bullet hole?!?
Latest: PrairieDrifter
Today at 2:24 AM
Interior
Taillight question
Latest: DatKat933
Today at 2:05 AM
Exterior
Forum statistics
Threads
48,413
Posts
1,066,780
Members
42,792
Latest member
WyldTinker
Members
Top