Recent content by Marcus

  1. M

    305 Decode

    No problem
  2. M

    305 Decode

    Best I could find was it was originally in a 1985 Impala according to the code CDJ
  3. M

    305 Decode

    Tell them it’s for a 305 out of 1973 model Chevy of some kind. Only advice I could give without the other codes on it. There’s codes on the front also that will tell exactly what it was originally in
  4. M

    Where is a good place to snake out the exhaust from after pipes meet

    Just run it out about a foot from the tire and let it point out. Get you an exhaust tip that’s angled and have it point downwards. No big deal on tire or gas tank. I’ve done several that way.
  5. M

    Heater core hose hookup

    Are your hoses in line vertical or horizontal? Should be the top hose goes to your water pump and the bottom hose goes to your intake.
  6. M

    Aftermarket Cam for stock 350

    Oil was everywhere on it. Needs taken apart and checked out. Which is why I’m researching parts to go back in it that will help it run a little better. It was put into a feed truck years ago and never got over 25mph for 15 years. It needs taken apart and gone through.
  7. M

    Aftermarket Cam for stock 350

    Yeah, I need an intake and carb for sure. Already has dual exhaust. Set of manifolds off an early 90’s model throttle body 350. .342 front and rear gears.
  8. M

    Aftermarket Cam for stock 350

    My budget is like $600. The engine runs. Just has oil everywhere which I’ve cleaned the outside really well. Just want it running for now but I want a better cam in it cause it doesn’t have a lot of hp. There’s been no loss of compression at all. Just not quite enough hp and growl to it.
  9. M

    Aftermarket Cam for stock 350

    Well I’m trying to do this on a budget to have a running engine that doesn’t leak, lack power, or have smog crap on it for now. I know for a fact that the block is solid but what is unknown is the cylinder walls and rings. Just trying to do everything right as possible on a budget. Hard thing to...
  10. M

    Aftermarket Cam for stock 350

    I know that I should send the block off to have everything done but I don’t have the $$ to do everything from inside out top to bottom.
  11. M

    Aftermarket Cam for stock 350

    Still trying to figure this out. Any thoughts on this kit? Should I get something else?
  12. M

    Aftermarket Cam for stock 350

    This is the kit I have been eyeballing. Just don’t know quite enough about all of the specific parts and numbers.
  13. M

    Aftermarket Cam for stock 350

    I know of very reliable engine guy 10 miles from here. I’m know I’m taking the heads and crank to him. The engine is not the factory engine for this truck. It originally came in a 1975 Nova police car if that changes anything. I just want it to run good, breathe good, and bump a little hp and...
  14. M

    Aftermarket Cam for stock 350

    1985 GMC K1500 with 3.42 gears. Everything is bone stock. Only thing I’m gonna do to it is take all the smog crap off. Take apart and rebuild it with all new gaskets, pistons, rings, cam, timing chain, freeze plugs, etc etc. I just want a little more hp and a deeper growl. Something to wake the...
  15. M

    Aftermarket Cam for stock 350

    Have a fully stock 350 4 bolt main. Looking into buying a rebuild kit that comes with a stage 2 cam. Curious on what everyone thinks about the stage 2 cam in a stock 350 4 bolt main. I’m not looking to get 400hp or anything crazy. Just a little something to put some ump into it. What do y’all...
See more

Latest posts

Forum statistics

Threads
42,129
Posts
909,788
Members
33,626
Latest member
Silverado9019
Top