Recent content by crusin242000

  1. crusin242000

    Fan blows fuse when turned on high speed

    I heard a pop. I will use my test light to search in the am. I am looking for areas to check and your input will sure get me started. The pop sounded like it came from the main panel under the dash by the drivers door area. Sent from my iPhone using Tapatalk
  2. crusin242000

    Fan blows fuse when turned on high speed

    I need your help . I have replaced the blower motor , resistor and high speed relay. It blows when you switch it on high , any input is appreciated as this truck was butchered on wiring from previous work. Thanks Sent from my iPhone using Tapatalk
  3. crusin242000

    Need help! Fasteners

    I have found a lot of help here in this group , I followed recommendations Andrew got my heater core replaced and with wiring diagrams provided from this group got blower working again . I went to install the duct work and the “mechanic” who worked on it didn’t keep them. Any ideas on how to or...
  4. crusin242000

    Wiring for blower motor

    They took the whole assembly out under the dash. Most of those wires and vac lines were still attached. What wasn’t was cut and I was able to figure that out. The firewall side of the equation is what is slowing me down. Your explanation made it easier to picture . I’ll respond when I have an...
  5. crusin242000

    Wiring for blower motor

    It has ac and heat , sorry for the delay in response . Sent from my iPhone using Tapatalk
  6. crusin242000

    Wiring for blower motor

    Hello , I have finally put all of my heater core and hvac parts in that were taken out by a shop. Now to connect all the wires. I don’t know where to hook up what as I didn’t wake it apart. Any diagrams or input will be much appreciated! Thanks , Eric Sent from my iPhone using Tapatalk
  7. crusin242000

    Heater core replacement

    Thanks! Do you know what size nuts / thread pitch to buy? Hate to ask so many questions, but you guys sure help me out ! Sent from my iPhone using Tapatalk
  8. crusin242000

    Heater core replacement

    Okay so just a regular washer or maybe a lock washer ? Sent from my iPhone using Tapatalk
  9. crusin242000

    Heater core replacement

    Okay . Just received the 3m strip caulk. Preparing before I start reassembling. Does anyone have recommendations on the fasteners? The nuts that came from the factory are almost all dinged up and not reusable. Should I go stainless or any suggestions would be greatly appreciated here. Thanks...
  10. crusin242000

    Heater core replacement

    It was taken out by a shop(hvac) what should I use to seal that opening ? Thanks Sent from my iPhone using Tapatalk
  11. crusin242000

    Heater core replacement

    I have now decided to replace my heater core. Simple and near completion. I have one question. Should I use some kind of adhesive on the firewall? I have the inner fender out so it will be easy to access the bottom bolts . Thanks in advance . Really a good group of knowledgeable guys on here...
  12. crusin242000

    Look forward to getting to know this site.

    Ok , after a little soap as suggested on the throttle cable , I went inside the cab with a small flat tip screwdriver and held the cable. A little pry and it went easy ! I used some super glue to put the gasket on the firewall after wiping and cleaning it with acetone to remove old debris...
  13. crusin242000

    Look forward to getting to know this site.

    I don’t have many pics of it. It has been in my family the entire time . 88,*** miles. I updated my profile pic to my son inside playing . Sent from my iPhone using Tapatalk
  14. crusin242000

    Look forward to getting to know this site.

    Thanks ! I have several projects on this truck I need to get done . This is just the most important . I paid someone to replace the heater core and vent window and it sat in his shop for a year. So I appreciate any help! Sent from my iPhone using Tapatalk
  15. crusin242000

    Look forward to getting to know this site.

    It isn’t . The same thickness. I’ve had someone hold it and I’ve gotten on the inside and tried to get it pulled through with a screwdriver Sent from my iPhone using Tapatalk
See more

Latest posts

Forum statistics

Threads
42,126
Posts
909,673
Members
33,618
Latest member
1975K20
Top