Recent content by chiefburns
-
Edelbrock Pro-Flo 4 - replacing my TBI any thoughts anyone done this?
I put the Pro flow 4 on my 72 Camaro and I love it. Driveability of it compared to the old carb system is amazing. I bought it when Edelbrock offered the free fuel sump, which saved me from having to run new fuel and return lines, new pump, etc. I am not a mechanic by any means but I was able to...- chiefburns
- Post #24
- Forum: Engine & Performance
-
Green Gas Monkey Wrecked Truck being rebuilt.
What surprised me the most was the original truck build by GMG. In one of the videos the robot voice guy shows of the interior, he pans past the original fuse block, complete with what looks like the original glass fuses. I would have assumed they would have replaced the entire wiring harness on...- chiefburns
- Post #55
- Forum: Garage
-
Tailgate Band Measurements
I bought a tailgate band for my 76 GMC and was wondering if someone who had one on their truck would send me the measurements to the bolt hole locations. I've tried the "grease on the bolt head" trick but I wanted to confirm the exact locations before I actually drilled them.- chiefburns
- Thread
- Replies: 11
- Forum: Paint and Body
-
79 C15 woes
Welcome from a fellow C15 owner in South Carolina!- chiefburns
- Post #8
- Forum: Introduction
-
Newbie from Eastern Washington.
Welcome from South Carolina. Cool ride!- chiefburns
- Post #30
- Forum: Introduction
-
Fitting a 76’ Grille in my 79’?
That would be awesome! I’ll send you my address, just let me know what the shipping is and I’ll pay for it.- chiefburns
- Post #27
- Forum: Exterior
-
Fitting a 76’ Grille in my 79’?
Did I see a "250" grill emblem in one of the previous pics? If so, I would love to take that off of your hand$ for you.- chiefburns
- Post #25
- Forum: Exterior
-
C-10 Nationals in Maggie Valley, NC
I follow them on Facebook and they've been putting updates on their page with these dates. IDK?- chiefburns
- Post #7
- Forum: Events
-
-
Add Side Trim Molding
I'm thinking of adding side trim molding and painting the inside area white for a two-tone look rather than just blue. I haven't decided on the roof yet because finding GMC cab corner molding is not an easy thing to do. Has anyone done this already and how much of a pain is it to do? I'm also...- chiefburns
- Thread
- Replies: 0
- Forum: Paint and Body
-
C-10 Nationals in Maggie Valley, NC
I took my grandson to it a few years back and he's been hooked on classic cars/trucks ever since. This was one of the trucks we saw there.- chiefburns
- Post #5
- Forum: Events
-
C-10 Nationals in Maggie Valley, NC
I just saw this... The C-10 Nationals open to all Chevrolet and GMC truck models is taking place September 24-26, 2020 in Maggie Valley, North Carolina. This awesome event is held at the Maggie Valley Festival Grounds and offers Top 50 Awards. Please share photos of what you will be bringing to...- chiefburns
- Thread
- Replies: 8
- Forum: Events
-
-
Best way to install new hood hinge springs?
I watched a video on YouTube where the guy screwed deck screws in between each spring loop, on opposite sides of each other, and it extended the spring enough to remove it. He did the same for the new spring and just backed the screws out to seat it back on the hinge.- chiefburns
- Post #13
- Forum: Tech Discussion
-
Storage tray behind the seat
Yep, that's it. Man, you can't even look at that thing hard without breaking something on it...but it is pretty cool.- chiefburns
- Post #6
- Forum: Interior
