Recent content by 83kid

  1. 8

    Replacing fan motor

    Got another and it was the same way, so i figure for some reason its made that way
  2. 8

    Replacing fan motor

    Hi, Went to replace my blower fan motor because its tired and doesnt spin too fast... Put it in and it made a ton of vibrating noise. Also, could see there are 4 shiny rivets on it on the outside with it in, and could see little tiny sparks on them every once in a while. Took it out...
  3. 8

    tbi to carb swap trouble !!

    Do NOT oogle the holes. Idiot who had my truck before me did, and it will blow the intake manifold gasket soon enough, already has once before i decided to buy the right intake. Edelbrock part number 2104, preformer intake, canted center holes to make it work You will leak oil and coolant...
  4. 8

    Starter

    The sound continues after its running, just right after it fires up and i move the key grom the start to run position the noise slows as one would just by friction, not immediate but wuickly, but gradually going down Replaced the starter in the truck before and it never made that noise, so...
  5. 8

    Starter

    Hi, Put in a new starter the other day. Installed correctly, and it makes a whir after the engine starts, i crank it, and if i let off because the engine starts it still does it. If i start the truck, i can hear it just the same. Its like the sound of a whinibg electric motor when somethings...
  6. 8

    What filter?

    Hi, truck has no fuel filter so im puttig an inline one in between the fuel pump and carb, what would you recommend? Found a good 40 micron one, russel preformace (on summit), should i be looking for something like a 10 micron or is that good? Has edelbrock carb, 4 barrel 600cfm, everyone says...
  7. 8

    Issues

    Fixed it, engines a bit carboned up anyways so it has a dieseling issue unless im running 93 in it, but for the issues on carb tuning and such it fixed it, oh yea rebuild it with a kit from summit, easy to do
  8. 8

    New intake and carb question

    Or, you can do it so its key on power... but only when the engines running, much better. So if you turn the key on and leave it on, your choke wont open an be ineffective if you forget, on the back of the block there should be a fitting for an oil pressure guage or sensor. Get the little sensor...
  9. 8

    Carbon buildup/issues

    Havent checked plugs but theyre within the last couple thousand miles new, timing is right i think.. Theres the toothed piece, where to the very left of the toothed piece is says 0 degrees, then there a red slider which it looks like someone screwed on thats over to the right of that, around the...
  10. 8

    Carbon buildup/issues

    Hi, So i have an 83 k10, with what i believe is a '90 350, mated to a 700r4 to np208 with what i believe are probbly 3.55's or something similar for the axle gear ratio The 350 has about 40k on the rebuild, mild comp cams cam, i can provide link if necessary, msd ignition, headers, and a...
  11. 8

    Hid headlight wiring

    This one has wiring for power from the battery, ground for each ballast, but then i need switched power to turn on the relay or as this kit calls it, the control module So normally it would plug into where the old headlight connectors which went right on the headlight pins but this truck has a...
  12. 8

    Hid headlight wiring

    Hi, So recently bought some sealed beam conversions from hidkitpros.com, with the bi xenon harness So my question is: where should i wire what would normally go to the stock headlight connectors? I have an isolation module, so that changes all the colors around, but the hid kit has a 3 prong...
  13. 8

    shake

    Only thing i think that may elimate this is that it only does the shake between 1st and 2nd, not in first, not in second, but between it.. could this still be it?
  14. 8

    shake

    What could i do to test for those? Also, my main question here is... Am i gonna have to do any work to the transmission? Seems odd that itsonly between 1st and 2nd no matter the little it of difference in speed your moving when it shifts
  15. 8

    No filter, making a setup

    Hi, So i discovered my truck has no actual fuel filter. No wonder why the carb was so damn dirty when i rebuilt it Has the one in the carb, but its just a mesh one so i assume it doesnt filter much of the actual fuel itself. I want to filter the fuel really well. So, i was thinking of having...
See more

Latest posts

Forum statistics

Threads
42,204
Posts
911,280
Members
33,699
Latest member
duckboy_17
Top