Dual tank delete

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Frankenchevy

Proverbs 16:18
Joined
Jan 3, 2018
Posts
5,957
Reaction score
7,406
Location
USA
First Name
Jeremy
Truck Year
Square
Truck Model
CUCV
Engine Size
Small
Me personally, I have been trying to figure out a way to link the two tanks. Not to hijack the thread, but I really want to keep the two 16 gallon tanks, be able to fill up on either side with 32 gallons from dry, and only need to run the one fuel pump.

I haven't figured that one out though.
You can run a cheap electric fuel pump from your secondary tank into your primary tank’s filler neck vent with a ‘t’. Not the sending unit vent.

3/4” brass barbed pex fittings fit well for the filler vent tube iirc.

This method does require you to have a switch in your cab to activate the secondary inline pump. You can use the stock selector switch and/or location though.

You’d still have to fill the tanks individually. There isn’t enough capacity on a 3/8 supply line to keep up with a gas station pump.

The alternative is a blazer/burb single tank under the bed.
 

Craig 85

Full Access Member
Joined
Jan 25, 2017
Posts
3,892
Reaction score
4,036
Location
Nashville, TN
First Name
Craig
Truck Year
1985
Truck Model
K30 SRW
Engine Size
454/TH-400/NP205
I have been trying to figure out a way to link the two tanks and be able to fill up on either side.

Back when these trucks were in production, there was a company that built a kit to fill both tanks at once. I don't know how well it worked, but basically it was a pipe that ran across the frame and had some type of "T" above the neck of each tank, then up to the filler neck.
 

Frankenchevy

Proverbs 16:18
Joined
Jan 3, 2018
Posts
5,957
Reaction score
7,406
Location
USA
First Name
Jeremy
Truck Year
Square
Truck Model
CUCV
Engine Size
Small
Back when these trucks were in production, there was a company that built a kit to fill both tanks at once. I don't know how well it worked, but basically it was a pipe that ran across the frame and had some type of "T" above the neck of each tank, then up to the filler neck.
You remember where the third filler neck went or did they figure out how to use the factory ones? The second would be interesting, as it seems fuel would need to go uphill somewhat.
 

Madhorn

Full Access Member
Joined
Jan 16, 2017
Posts
618
Reaction score
1,311
Location
AR-Arkansas
First Name
Ken
Truck Year
1977
Truck Model
K10
Engine Size
5.3/NV4500/NP205/4:56 gear/35in tires
My 77 originally had two 16 gallon tanks. While doing the 5.3 build/conversion I had considered a single 35 gallon blazer tank but went with a single 16 gallon tank on the drivers side, didn't want to mess with dual tanks. I have had the selector valve leave me stranded a couple of times. At this time i need to stop for a fill up every 3 to 4 days with daily driving to work (130ish miles). One day I may go back and install the 35 gallon tank and locate the filler behind the drivers side tail light. BTW, latest MPH was 15.2 for daily commute while running AC.
 

73c20jim

Full Access Member
Joined
Jun 11, 2018
Posts
2,282
Reaction score
2,924
Location
Tombstone, AZ
First Name
Jim
Truck Year
1973, 1973
Truck Model
C20 2WD Custom Deluxe. C10 2WD Base Model
Engine Size
350 CID 195/260 HP Goodwrench crate, 400 CID 2bbl
If it were me...
I’d wait for the dual bed.
16 gallons go fast

Other than the left side fuel fill hole, what is the difference between the two beds?

I'm thinking of removing a right side section of an old bed around the fill hole , and welding it into my current bed on the left side.

Comments???
 

Double d

Junior Member
Joined
Aug 17, 2019
Posts
8
Reaction score
2
Location
Key west Florida
First Name
Double d
Truck Year
1986
Truck Model
C20
Engine Size
350 sbc
Other than the left side fuel fill hole, what is the difference between the two beds?

I'm thinking of removing a right side section of an old bed around the fill hole , and welding it into my current bed on the left side.

Comments???


The stock bed has so much rust not surface rust it’s not really worth restoring.
 

TerryRH

Full Access Member
Joined
Mar 28, 2019
Posts
477
Reaction score
906
Location
Jacksonville, NC
First Name
Terry
Truck Year
1987
Truck Model
R10
Engine Size
350ci
Curious, can y'all not mount a Blazer, or Suburban tank? I like my 42 gallon tank.

Back when these trucks were in production, there was a company that built a kit to fill both tanks at once. I don't know how well it worked, but basically it was a pipe that ran across the frame and had some type of "T" above the neck of each tank, then up to the filler neck.
I would absolutely love to have a 42 gallon tank! I drive 100 miles a day, so with low MPG, a big tank is a must. That's why the 16 gallon tank is so annoying. I really wonder if I can mount the Suburban tank, I'll settle for the Blazer tank though haha
 

eskimomann209

Full Access Member
Joined
Jan 9, 2019
Posts
1,849
Reaction score
2,000
Location
Modesto
First Name
Marcus
Truck Year
1973
Truck Model
C10
Engine Size
5.3
I have an LS it gets great mileage too.
But 16 gallons is still every three days.
I drive about 70 miles a day probably on average the old girl sees high revs and 80-90 MPH
And our gas prices are terrible in commicalifornia
 

eskimomann209

Full Access Member
Joined
Jan 9, 2019
Posts
1,849
Reaction score
2,000
Location
Modesto
First Name
Marcus
Truck Year
1973
Truck Model
C10
Engine Size
5.3
The stock bed has so much rust not surface rust it’s not really worth restoring.
@73c20jim
Also these beds unbolt.
Might there be a way to swap side panels?
Or is it too rusty on the entire sides?
As for me yaaas I’d weld them if It’s what I wanted/ needed
 

Latest posts

Forum statistics

Threads
42,068
Posts
908,347
Members
33,544
Latest member
Twistedgmt400
Top