Search results

  1. S

    1 piece floor pan?

    https://www.oerparts.com/shop/1987/gmc/truck/parts/?q=Floorpan%204WD
  2. S

    Differential setup

    Set it up the same...thinned it and added resistance for better marking...here's what I got. Tell me what you guys think now.
  3. S

    Differential setup

    Ok...well considering that Iʻm a rookie in this realm...it sounds like most of yaʻll are saying I should clean off the existing compound, buy some new compound, which apparently Iʻm gonna have to go through Amazon to do instead of being able to get it today :(, thin out my compound with ATF, and...
  4. S

    Differential setup

    Hey fellers...need some insight and opinion here...take a look at these pics and you fellas tell me where you think I'm sitting. Backlash is already at around 5 thousandths...just trying to get contact pattern in the green.
  5. S

    Gentlemen, take a look at this wierdness...odd "crack" in diff housing

    Alright, my buddy put me in touch with an axle guy...Iʻve been right all along. Itʻs a non-issue because all that area is is shaft pass-through. All I need to do if I want to feel good about it is what I said...light deburring and continue. Sorry to bug you guys. Iʻll leave the post here in case...
  6. S

    Gentlemen, take a look at this wierdness...odd "crack" in diff housing

    Here..this is from outside and one is from inside.
  7. S

    Gentlemen, take a look at this wierdness...odd "crack" in diff housing

    No...Iʻm not talking the seat for the race. Let me see if I can take the picture and circle the areas Iʻm talking about.
  8. S

    Gentlemen, take a look at this wierdness...odd "crack" in diff housing

    GM 8.5" 10 bolt
  9. S

    Gentlemen, take a look at this wierdness...odd "crack" in diff housing

    Got the axle housing emptied out for rebuild and was cleaning it up this morning. After some cleaning, I noticed the "cracks" youʻll see in the pictures. Now looking at the drivers side, that one looks like itʻs there for a reason, cast during manufacturing. The passenger side however...
  10. S

    8.5" 10 Bolt Outer Axle Seals / Modification

    Iʻm specifically asking about outer axle tube seals for a 10 bolt front. Iʻve found them for D44, but parts arenʻt interchangeable until knuckle and out from what I know. I just cleaned my tubes out and it had a massive buildup of mud and gunk that I had to clean out. I would really like to...
  11. S

    GM 8.5" 10 Bolt Rebuild / Knowledge, Opinions, and Advice Requested

    I totally forgot to ask this one though. Is it ABSOLUTELY necessary to replace ALL steering arm fastening parts? Studs, conical washers, and nuts?
  12. S

    GM 8.5" 10 Bolt Rebuild / Knowledge, Opinions, and Advice Requested

    Sweet! So far I'm on the right track then. I've just about got the 10 bolt for the front done and buttoned up. I'm just waiting on a few parts to finalize it. I mainly went in to both of them to inspect and change the wear items like ball joints, bearings, races, seals. I got these axles along...
  13. S

    GM 8.5" 10 Bolt Rebuild / Knowledge, Opinions, and Advice Requested

    As I've mentioned in a few posts already, I am rebuilding a 14 Bolt axle that will go in the rear of my 1974 K20, and a 8.5" 10 bolt that will go in the rear. I wanted some different perspectives on a few things. I am NOT a rock-crawler, and nor do I intend to be with this truck. This will be...
  14. S

    Front 10 Bolt Axle Assembly

    Ok, now that I've seen someone else mention the sleeve protruding through the bottom quite a bit, like mine is, I have to ask the question. Is it a problem if that sleeve is protruding through the bottom?
  15. S

    New K20 owner!

    The axle has already been broken down and all parts cleaned primed and painted. Iʻm in the process of putting it back together already.
  16. S

    New K20 owner!

    And the rest since I can only do 5 at a time
  17. S

    New K20 owner!

    Hey guys...just got the pics of the truck. Apparently I chose to simply get to work on it right away instead of taking a single picture of it, so Iʻm glad you guys reminded me to do that since everyone is asking for pics.
  18. S

    GM 8.5" 10 bolt nightmare.

    Well, I have an update...with more questions. I tore that 10 bolt all the way down because 1 side was pretty much open with no locking hub or anything and a spindle rusted to hell. And of course theres the "donʻt trust it without checking it" factor. Anyhow, before I ask these questions I do...
  19. S

    GM 8.5" 10 bolt nightmare.

    Hey Bextreme04! Thanks for the reply. Pretty much right after I made the posts I found the answer finally though. As much as I wish I didnʻt, I do have to remove the steering arm from the knuckle. I was really hoping for a miracle answer but I pretty much knew when I looked at it. The ball joint...
  20. S

    GM 8.5" 10 bolt nightmare.

    Hey all, So Iʻm new here, as in just posted an intro before this. And Iʻm a new K20 owner...which is what my question is about. Specifically the GM 10 botl front axle. Iʻve got it torn down about 85% but am stuck on removing one last ball joint. Itʻs the one thats right by the steering arm. Do...
  21. S

    New K20 owner!

    Hi all! Iʻm Scott and I just recently bought a 1974 K20. It came with a brand newly built 350 bored 30 over and replacement axles for the front and rear...although those need work and are the current effort. Annnd that brings me to precisely why I joined this group...I needed another forum to...

Latest posts

Forum statistics

Threads
42,184
Posts
910,863
Members
33,676
Latest member
jodygraham64
Top