Search results

  1. X-cabsquarebody

    91 4L80E 4X4 trans, Western NC

    4L80E trans out of my 91, 4X4 Crew Cab. It has a GM remanufactured sticker on the housing. Trans worked great when pulled about 6 months ago. Comes with torque converter, and dust shield. $600 I do have the computer that run the motor and trans, and the wiring harness. The wiring harness...
  2. X-cabsquarebody

    TBI 454 Complete. Western NC

    I have a complete TBI 454 out of my 87 ton truck. The reason I pulled it was no power over about 30 MPH. It ran great, starts easy, no check engine light. I put a 8.1 in its place. I was told 52000 miles is the correct mileage on the truck, but can't prove it. I now wish I tried a 750 Holley and...
  3. X-cabsquarebody

    Calibratable DRAC Module For Electric Speedometer

    I have a DRAC module for 90-91 trucks with electric speedometer. I have soldered in a set of dip switches so you can calibrate your speedo for different tire size, or gear ratios. I have tested and works great. $150 for forum members.
  4. X-cabsquarebody

    TBI harness and computer. wanted

    I need a harness to run a tbi 350. And computer too. I can make it stand alone. Don't need the under dash stuff, just from the computer to the motor, and the computer. Thanks
  5. X-cabsquarebody

    Painted an old dump truck.

    Me and a friend painted this C30 this weekend. The truck has a 292 six banger with A/C , power steering, and power brakes. Radio delete, dome light delete. 40,000 miles on it. its a cool little truck. First time shooting paint in 8 years.
  6. X-cabsquarebody

    Wanted.... Temp display rear view mirror.

    A few months ago, a forum member posted about selling rear view mirrors with temperature display. For the life of me,,,, now I can't remember who it was. Looking for a rear view mirror with temp display. Need all wiring and sensor too. My crew cab doesn't have a mirror, and thought that...
  7. X-cabsquarebody

    Need help with 4l80e not shifting right.

    I put an 8.1 / 4L80E in my 91 craw cab. I cut down the factory harness. Engine runs great, Trans is not shifting right. The Trans its out of an 2002 ton truck. I put a filter in it before I installed it. The Trans holds 1st gear till the motor is turning about 5 grand, and you have to lift off...
  8. X-cabsquarebody

    Reupholstering a Bench seat. Picture Heavy

    Just showing how I recover a bench seat. Remove covers off seats by cutting the hog rings, and unhooking the J channel. Cut reference makes in the old covers seams, marks are called darts. The darts will be transferred to the new cover and aid in getting the cover pieces...
  9. X-cabsquarebody

    Hydraulic Flaring Tool

    I bought a Mastercool hand held hydraulic flaring tool. The thing is awesome! I will flare push connect, GM fuel line O-ring flares, Double flare, and metric bubble flare. http://www.ebay.com/itm/360316094548?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649
  10. X-cabsquarebody

    Moving sale

    A friend is moving and has to get rid of a lot of stuff. Here is a list. In Brevard NC. Western part of the state. Set of 10 bolt axles, front and rear, 3.42 gears, and one front housing all for $300 OBO Rare 5 lug dana 60 rear, 5 on 5 1/2 lug patern, out of a J-4000 Jeep truck. 4.10...
  11. X-cabsquarebody

    Charlotte Auto Fair

    Went to the Charlotte Auto Fair last weekend. Lots of new and used parts vendors, and cars for sell. Held at Charlotte Motor Speedway.
  12. X-cabsquarebody

    Early LS Computer on an 1986 TPI

    I know its been done. I know there is a kit to do this, ($1800).... But I always have 10 million side projects going on at the same time, I have 4 TPI set ups, and I have an extra 12200411 computer, with plugs. Has any body here played around with this stuff? If so was it worth it...
  13. X-cabsquarebody

    How To Build Custom Door Panels

    There is a million ways to build door panels. This is one of the easiest ways and they mount like the original panels. First, I cut the center out of the my old door panels. The outer part of the panel has all the mounting stuff in it, clip holders, and screw holes. Cut a piece of 1/4...
  14. X-cabsquarebody

    Any One use EFI Live?

    I'm swapping in a 2002 vortec 8.1 in my truck. I have cut down a factory harness, and mounted the motor on a stand. I wanted to start the motor and run it before I put it in, but it will not start. I can prime it and it will hit but not run. Once it tries to start,the injectors shut down. I need...
  15. X-cabsquarebody

    Converted to 4 wheel drive.

    A few years back I got a call about a 74 Suburban that was headed to the crusher. The owner was trying to sell me the doors and fenders. But when I got there, I struck a deal on the whole thing. No motor or trans, but not in bad shape over all. I had an Olds 455 and a trans that I was going to...
  16. X-cabsquarebody

    Custom Console Build How To

    I'm going to show how to not only build, but mock up and cover a custom center console. The pictures are from a build in a 48 Chevy, but this is how I built my console in my truck. First, use poster board, or card board to make the basic shape of the console. This will show how it will...
  17. X-cabsquarebody

    Hey Ya'll

    I tripped across this forum a wile ago. Just signed up cause there is a lot of cool stuff on here. Hope that maybe I will be able add to the forum with my projects. Thanks. 1991 CC 3500 4X4, currently swapping in an 8.1 1987 K30 1980 C10, bagged and body, Daily run around 1980 C10...

Latest posts

Forum statistics

Threads
42,127
Posts
909,680
Members
33,620
Latest member
JoshuOne
Top