Search results

  1. 87_stepper

    Grille Trim

    Has anybody used Goodmark trim pieces everyone says they are better than the LMC junk anyone that can back up this thanks.
  2. 87_stepper

    Grille Trim

    Any members have some mint OEM tucked away that they are willing to sell?
  3. 87_stepper

    Stepside fenders on or off for paint?

    mine was painted in pieces and then assembled as others have stated you wont get good coverage under the lip and on top of the fenders also used sealer when bolting fenders back on 3m strip caulk I believe, then sprayed rock guard in the fenders and along the box turned out beauty.
  4. 87_stepper

    85 C10 Fan help

    Those sensors are all resistance based probably a wax pellet type and are spanned to be accurate within a certain range having a bad ground will move that reading, example good ground 0-100 bad ground 30-130 move your alligator clips to the battery ground and try again.
  5. 87_stepper

    LMC Mirrors Chome VS Stainless Whats the difference?

    I am fairly picky with parts but was surprised when I ordered the LMC stainless premium mirrors I reused my original GM mounting brackets only used the stainless components and they fit pretty decent and the finish is good.......everything else from LMC has been dissapointing though.
  6. 87_stepper

    Grille Trim

    Yeah I have tried all this, thanks though
  7. 87_stepper

    Grille Trim

    Hey Guys, really hit a wall with my build I have been looking for mint grille trim in Alberta for 2 years now with zero luck I ordered the LMC junk against better judgement and is fairly disappointing with quality is there any quality repo's out there or is it all gonna be the the same from...
  8. 87_stepper

    Perimeter bolt or center bolt valve covers?

    I use Fel pro 1628 Amazon had the best pricing and free shipping for me nice and thick blue silicone with metal insert to hold the shape
  9. 87_stepper

    Does my engine have a chance of living?

    Clean up exactly like you did buy some 15-40 and a few filters mix the 15-40w with some diesel 50-50 run at idle for a couple minutes pull the filter cut open, drain repeat twice I have had great results also used ATF which is high in detergents.
  10. 87_stepper

    Time for a new radiator

    I am in the garage today I can send measurements if you put a level across the rad support and take a measurement to the ac compressor I will do the same.
  11. 87_stepper

    Time for a new radiator

    Upper Ac delco 26064X Lower Ac delco 24205L Have to trim the upper a little bit to get clean bends but otherwise fits perfect
  12. 87_stepper

    Rust and water in cylinder

    I used brake fluid on large stationary nat gas engines the brake fluid will absorb the water as well as prevent further rusting and when your ready to start provide additional lubrication.
  13. 87_stepper

    Another Serpentine conversion w/smog pump question

    The 96-98 limits you on valve cover options which in turn dosent allow for roller rockers etc in case you were planning engine work down the line. I reccomend the 93-95 serpentine setup
  14. 87_stepper

    Time for a new radiator

    Just finished my Cu730 big block Rad and Flex a lite 295 fan install give me 6 months and I will let you know how well it cools.
  15. 87_stepper

    Stepside Tailgate Paint

    Hey Guys, looking for ideas on how to keep the tailgate from rattling around and chipping/scratching the tailgate and inside of my freshly paint box. Thought about using 3M?

Latest posts

Forum statistics

Threads
42,065
Posts
908,290
Members
33,542
Latest member
willyg
Top