Search results
-
What have you done to your square lately??
If it’s clean - it will stick, appreciated slowly but surely -
What have you done to your square lately??
Took the weekend and installed Design Engineering Inc cut and form transmission tunnel heat shield, managed it two pieces and heat tape, *Note - easier with a friend than alone for placement lol -
Dually Fender Attachment
I do not have the cast fender trims on mine, they are like inner fender liners for sure. Would really appreciate some up close pics sir!- Tank6x2
- Post #22
- Forum: Paint and Body
-
Dually Fender Attachment
Was it plastic/steel, manufactured or fabricated- is it available or a unicorn?- Tank6x2
- Post #19
- Forum: Paint and Body
-
Dually Fender Transition Cap Piece
So I’m not sure what I’m looking for, I saw few posts, one with a transition fender gap piece, but I’m curious what was done from gm factory with the Dually fender to transition the fenders/ protect the fibreglass at all - or was it just the cap and fibreglass was truly left to the elements of...- Tank6x2
- Thread
- Replies: 1
- Forum: Paint and Body
-
Dually Fender Attachment
Was there anything else for the inner fender/ just the fibreglass exterior dually flares? Did gm not make anything?? @bucket- Tank6x2
- Post #17
- Forum: Paint and Body
-
What have you done to your square lately??
Creeping FBMP today, does anyone know for a fact if the ram horn manifolds fit without interference on a 350ci SBC?? -
What have you done to your square lately??
Free will is a wonderful thing isn’t -
What have you done to your square lately??
Agree with you, one exception- your spreading the load of the truck over 24 rivets for just the rear (light end) of the truck, as much as I wouldn’t think it move on just the cab, I would bet an engineer at GM would say it’s only meant to support the body structure where as the frame crossmember... -
What have you done to your square lately??
I would shoot for suspension or frame, body mounts are solid but wouldn’t trust them outright to hold the weight of the truck. IMO which ain’t worth much to most… if you feel safe, and nothing happens- we will continue to see you around. If not …. -
What have you done to your square lately??
Spent the weekend prepping and painting the bottom side of the cab and disassembling the hardware on the box. -
What have you done to your square lately??
Been a few weekends preparing the bottom of the cab, filling pin holes with weld, knocking as many dings flats as possible and finally forcing self etching primer into the seams before sealer went on, polishing off Easter weekend with a free junkyard cut out seatbelt nut and getting it welded in. -
-
What have you done to your square lately??
Starting to think adhd/ocd are a bad combination to have - should I continue with the cab floor dings or just stop and finish with metal prep:banghead: -
What have you done to your square lately??
Started the weekend getting the mill scale off - leftovers from lasering, cleaning off residual tight spot rust it couldn’t reach, good weekend! -
What have you done to your square lately??
Time to install some 1/4 turn valves -
-
What have you done to your square lately??
He did bottom of the cab and box for roughly 650-750usd -
What have you done to your square lately??
140000$ the guy said.. :( -
What have you done to your square lately??
Because we are all kinda like magpies in this group - all like shiny, hired a contractor to laser all my parts, bottom on my cab/box - so happy to see progress yesterday!! -
What have you done to your square lately??
Managed to strengthen the wheel Dollie’s today, and get a hand cleaning up the shop, final sweep tomorrow and ready for a busy Monday of rust removal on the cab and box floor -
What have you done to your square lately??
I’m not sure if you have a shop or in a warehouse- I need your space - I would look less cluttered lol -
What have you done to your square lately??
What program are you utilizing? -
What have you done to your square lately??
Working on the axle, drilled out brake line passageways through the bag supports and started cleaning
