Search results

  1. MrMarty51

    86 gmc jimmy 383 stroker build

    X2 of what He said /\_/\_/\_/\
  2. MrMarty51

    4 bolt main caps

    many years ago I made that mistake. The block had to be sent off to get line bored after a used cap was found.
  3. MrMarty51

    197x dodge 3/4 Ton pickup truck 4x4 axles.

    14 bolts on the covers ? probably then is a 60 series. My 59 W100 Power wagon has one ton units under it from the factory. :Caffeine:
  4. MrMarty51

    Noise Coming From TC/Flexplate

    Try unbolting the convertor from the flex plate then moving the convertor towards the transmission, that might give You enough room to see in there and make a better determination as to if the FP is cracked.
  5. MrMarty51

    Wiper motor turns continuously in the same direction

    Welcome to the forum 7985. Try as Matt69olds suggested then reply back Your finding please.
  6. MrMarty51

    New, help please!

    :welcome:
  7. MrMarty51

    Vss check engine

    Did You install the reluctor wheel from the old TC into the 205 ? If the 205 has the speedo gear then the appropriate reluctor wheel needs to be installed.
  8. MrMarty51

    Fuel Tank Selector Valve Leaking

    It does require some new wires to be run from under the dash to the fuel selector valve.
  9. MrMarty51

    Fuel Tank Selector Valve Leaking

    I converted My 78 over to the motorized valve and with that began setting it up for a TBI conversion. All I now need is a set of fuel tanks from an 87 and the fuel pump/sender units and I`ll be good to go. Unfortunately, it does take the addition of some extra wires. Fuel gauge on Mine was...
  10. MrMarty51

    What have you done to your square lately??

    Yeah, hard pack snow was plowed against it, wheel climbed up and over before she knew what was going on. Back side had no snow against it so could not just back on out, frame high centered on the wall, front wheels about two feet from touching solid ground. LOL
  11. MrMarty51

    Time for this beast to get a CB Radio LOL

    :happy175::happy175::happy175: have a couple of old CB radios and an old base station that was left in the house next door that I bought. {the property} I been thinking of installing one in the 2000 K3500 since it is the road truck. I need to hang an antenna and see if any ofum works before...
  12. MrMarty51

    What have you done to your square lately??

    That's too bad about the plow hinge bar. Can a new one be built ?
  13. MrMarty51

    What have you done to your square lately??

    Yup, dropped the front end over a retaining wall, through the process the left side tie rod adjuster got bent. :Caffeine:
  14. MrMarty51

    What have you done to your square lately??

    Insttalled the battery and fired it up. Might need a spare four weeel drive if the wifey ruins My 2000 K3500 like she once did. :banghead::Caffeine:
  15. MrMarty51

    Hello from Seattle Area - 1978 Chevrolet K20 Intro

    Welcome from eastern Montana.
  16. MrMarty51

    Hello friends!

    I too am curious about that. I converted the full time in My 78 to part time and now I am thinking I should have left it alone. Only good way to do that is to find a 205 NP and mount it in, I cant find one in these parts that will fit behind the TH400 transmixer. Be a lot easier if it was a...
  17. MrMarty51

    Any bikers?

    I got a few of them too. Hiatwatha, Hawthorn and a couple of others. My daily driver is an old Raleigh Mountain bike, not near as old as Yours though. :Caffeine:
  18. MrMarty51

    Question about backfire on throttle release

    Used to be GM installed a mechanism on the carb linkage to slow the closing of the throttle plates to prevent backfire.
  19. MrMarty51

    Any bikers?

    Getting the transmission on the 74 T-150 Triumph back together, finally after laying around for a year. :Caffeine:
  20. MrMarty51

    1978 K20 16 x 6.5 OEM Steel Wheels

    Ford and Dodge wheels of that vintage have a larger center hole.
  21. MrMarty51

    Guess The Tool

    Looks like You dressed down the screw head so it would fit inside of the retainer of a slide hammer seal puller.
  22. MrMarty51

    Any bikers?

    Aeromacci is now Cagiva.
  23. MrMarty51

    Any bikers?

    Nope, not yet. :happy160::happy175::happy175::happy175: I never plan on riding fast when I go on a drive, its just something happens in Mine head that says TWIST THE BITCH. :Caffeine: Other wise I`d probably put on a helmet before leaving the propitty.
  24. MrMarty51

    Any bikers?

    Nope, at that speed it is just a very quick glance at the watch on the wrist. LOL It is all a person can do to hang on too, gripping fuel tank, feets on rear pegs and knuckles turns white and the force of the air makes a persons face sting too.. :happy160::happy175::happy175::happy175:
  25. MrMarty51

    Any bikers?

    My heart leaped when Jerry said they had that bike at their farm. :Caffeine:

Latest posts

Forum statistics

Threads
45,961
Posts
997,031
Members
39,165
Latest member
twitch1989
Top