Search results

  1. Rickf

    Either this part is unavailable, or I don’t know where to search.

    Get the metal cutting tools out and start fabricating. I have never seen that piece on any replacement inner fender. The fenders that have it rot out because it is a trap for road chemicals.
  2. Rickf

    1977 C10 AC not working, solution suggestions

    I took the most economical (cheapest) route and replaced the two pressure sensors, took everything apart, flushed everything, changed o-rings, added pag oil and charged it with 134a. It pumps out 40 to 45* air, I'd like to get it a little cooler incase I want to store dairy products.
  3. Rickf

    '73-'76 turn signal switch not universal

    Most likely, the directional switch looks newish and doesn't have the factory hard as a rock grease.
  4. Rickf

    '73-'76 turn signal switch not universal

    My '74 has the adapter harness, compliments of the previous owner.
  5. Rickf

    I need help and to know what this truck is worth

    Bring a trailer.... and a chain saw. Run the VIN thru local police, RMV or whatever agency is appropriate in NC.
  6. Rickf

    Recommend me a cheap

    A mortar tub or plastic 55 gallon barrel cut to size and gasoline or kerosene.
  7. Rickf

    468 bbc high compression

    If it was mine, I'd make sure it had the largest radiator known to mankind that would fit and use Evans waterless coolant.
  8. Rickf

    Taillight Fuse blows when put in Drive

    Maybe the issue is in the headlight switch? Could try to dis-connect the tail light harness from the firewall and see what happens.
  9. Rickf

    Left hand dipstick

    Somebody sells a flexible dip stick. I don't recall the vendor (maybe Lokar) it's been a few years/decades.
  10. Rickf

    Bed Support "Cross Sill" Options

    If you're not looking for a 100 point trophy, what about box/rectangular tubing? I will neither confirm or deny I've used PT 2x4's.
  11. Rickf

    Looking for headlight Threaded Inserts/Plate Nuts

    I've used retro-motive brand from amazon. Qty.8- #1774-8
  12. Rickf

    5.7 to 6.2 diesel engine

    Does the th350 have the BOP bell housing pattern?
  13. Rickf

    How much for my old bed?

    Wouldn't hurt to put some lumber between the cab & bed when lifting in case it gets away from you. I see a lot of welding and replacing of rotted sections of the rear cross-brace and floor. If the rest of the under side is as rough, the value drops significantly.
  14. Rickf

    3 on the tree problem.

    You might try disconnecting the linkage at the transmission and with the rear safely off the ground, see if you can get it in gear. This will narrow down where the issue is.
  15. Rickf

    78 gmc fiberglass body filler question

    You might need to grind your welds down a little more.
  16. Rickf

    Bad dash

    Maybe pack the holes with JB weld then re-drill? I've not had good luck with PVC or ABS cement.
  17. Rickf

    What size press (12 or 20 ton) for automotive

    I eventually bought HF's air assisted 20T bottle jack for the press, it's a lot quicker than the hand pump. As an added bonus I've used the original to jack up my skid steer for installing winter chains and to prop up sagging floors in old houses.
  18. Rickf

    Tranny wiring

    Who took it out? Why is the wiring missing?
  19. Rickf

    Where can i find this??

    Have you tried a salvage yard?
  20. Rickf

    80 C10 "Nemo" Build - Started as: Front frame buckled…

    If it was mine and ALL the damage is in front of the control arms, I'd have a frame shop fix it.
  21. Rickf

    454 intake manifold gaskets not sealing

    There is a difference between "peanut" port and round port gaskets.
  22. Rickf

    Clutch issues

    My '74 has a huge return spring under the dash, not sure if other years are the same.
  23. Rickf

    Lost my keys to 86 c10. Ignition Lock Cylinder, can I still remove it with no key???

    Wouldn't hurt to get an extra snap/retainer ring in case you f*** it up taking it out like I did.
  24. Rickf

    Tailshaft / Driveshaft yoke - how far out from the housing is ok?

    You may be in the market for a longer driveshaft. Look for a shop in your area for an "expert" opinion.
  25. Rickf

    New England Events?

    Brooklyn CT, Amherst NH, Thompson Speedway CT and Stafford Motor Speedway CT are a few of hunting grounds I've been to many years (decades) ago while looking for parts.

Latest posts

Forum statistics

Threads
45,951
Posts
996,759
Members
39,149
Latest member
metro247
Top