Search results

  1. legopnuematic

    Steering Wheel Too Close '84 C-10

    I've never messed with them but corvettes and some other GMs had telescopic columns. Not sure if they would end up shorter or longer than a truck column.
  2. legopnuematic

    1984 Chevrolet k10 700r4 id help

    A 700r4 should have the original partial vin stamping on the passenger side rear above the pan rail. If it has a tag adhered to it that would, to me suggest its been replaced/rebuilt at some point.
  3. legopnuematic

    Hello First Post/First Squarebody

    Welcome from Missouri.
  4. legopnuematic

    85 vent windows

    I looked at them on AMDs site, 73-80 they appear to be the two piece seal design? Like OE? Wasn’t it that the later one piece seal design were the only ones that used to be available as a new assembly?
  5. legopnuematic

    dose anyone have any good pictures of a 3inch body lift

    I don't mean to drag on the double/stacked frame thing, but I found a couple more pictures of them: See @idahovette they aren't all Phords :)
  6. legopnuematic

    What have you done to your square lately??

    @Moodyalaskan funny enough I do have one of those and was using it. I trimmed a little more and was able to get things to fit. With that I was able to get the MSD distributor stabbed back in and everything hooked back up. It runs again. Now I need to get to work on rebuilding the original...
  7. legopnuematic

    Seams that need sealed?

    From the factory the seam sealer would have been in-between the panels before they were spot welded, the squeeze out would have been wiped I guess to smooth it. If you want to smooth the spot weld dimples thats a personal choice. Definitely use a 2k seam sealer. In my opinion absolutely...
  8. legopnuematic

    Think I found a somewhat rare truck

    I’d say you’d be more likely to find a short bed step side 454 C10 that does have the F44 rpo (big ten/heavy half) than not, as (until 1979) that would get you a truck without emissions equipment. The muscle truck thing really started with the F44/F150/D150s. And with the general ‘Truckin’...
  9. legopnuematic

    Think I found a somewhat rare truck

    If it’s a C10, a 454 was an option, not available for a K10
  10. legopnuematic

    1985 C20 6.2 diesel A/C repair

    Craig, it looks like your picture/link didn’t attach.
  11. legopnuematic

    Mar-K Truck Toolbox for Stepside

    I built a fender well, or ‘porkchop’ (never heard it called that either but I like it) box as a high school metal shop project for my 76. These aren’t great pictures, but it has the upper compartment and then the lower area. The big difference between mine and commercial ones is it tucks under...
  12. legopnuematic

    1985 C20 6.2 diesel A/C repair

    I would first get a set of manifold gauges (and a vacuum pump) hook onto the high and low pressure ports. If you have pressure in the system, then you should be able to install belt and move the selector into an A/C position and see if it will cycle. (Someone correct me if I’m wrong here)...
  13. legopnuematic

    Old77’s GMT400 SWB 4x4 5-speed project/DD

    Every problem has a solution: Or coil springs and link suspension… :)
  14. legopnuematic

    Old77’s GMT400 SWB 4x4 5-speed project/DD

    I’m not familiar with how the lower ball joints are configured on those trucks, does the control arm have a ‘pocket’ for the joint to slot into? Where both sides of the joint are touching control arm? I’d probably go carbide burr on die grinder to whittle away the rivets just below the parting...
  15. legopnuematic

    dose anyone have any good pictures of a 3inch body lift

    Out in the Midwest at least, stacked frames were kind of ‘common’ at one point. Not really on drivers, but county fair type ‘exhibition’ rigs. Not really finding a lot of pictures, but they are out there, or were.
  16. legopnuematic

    Dana 60 spindle nuts

  17. legopnuematic

    Dana 60 spindle nuts

    From the outer bearing outward, the keyed (toothed) washer, nut, “spider,” then second nut. The spider should have the prebent tabs facing towards the differential, then one of the flat tabs bent over into the outer nut. Whatever lines up to a spanner groove. I’m not sure if it matters, but...
  18. legopnuematic

    dose anyone have any good pictures of a 3inch body lift

    That’s what stacked frames are for
  19. legopnuematic

    Best Truck Roof Top Tent for Weekend Camping?

    But when they get high centered on a curb in the Starbucks drive thru and have to camp for the night they will be ready.
  20. legopnuematic

    Best Truck Roof Top Tent for Weekend Camping?

    Enough said.
  21. legopnuematic

    Finally got a running 65 C10

    Fixed them for you
  22. legopnuematic

    Two Squares Every Day

    Welcome from Missouri.
  23. legopnuematic

    New from Iowa

    Welcome from Missouri.
  24. legopnuematic

    What have you done to your square lately??

    Lowered the 76 down to work on it some. Started on new plug wires I love my squares, but man I really don’t care for working around the A/C stuff, seems like it is always in the way. The nice R&M wire looms I have are meant for a small block with A/C. Guess what hits the compressor? That’s...
  25. legopnuematic

    First square body

    Welcome from the Saint Louis side of Missouri.

Latest posts

Forum statistics

Threads
45,934
Posts
996,393
Members
39,138
Latest member
Dadoo
Top