Search results
-
What have you done to your square lately??
Put new interstate battery in her truck. She mentioned multiple times she doesn't like the green. :rolleyes: Installed new plug wires. Blue as requested. -
What have you done to your square lately??
Was it stuff you bake for high heat? VHT has you do that at 200° for an hour. -
What new tools have you got lately?
Any recommendations on a spark plug crimper. Is my cheap a$$ gonna have to spend $100? -
What have you done to your square lately??
What gauges are in there? Do you have in a build page? Sweet... -
What new tools have you got lately?
I love the flaring tools. I was looking at something but more basic. And damn, I didn't know I needed a back probing kit?! -
Long time listener first time caller, or whatever...
:welcome: from Texas. Did you send a pic? No one asked...McWha?- Sgt Gus
- Post #11
- Forum: Introduction
-
What's this dohicky
I didn't think about running denatured alcohol through that weight proportioning valve though...I did push air through to clean out. Hopefully any o-ring etc are ok. :rolleyes: We also figured out master cylinder shot it had been sitting empty for the rears for so long. Picking up new delco... -
What have you done to your square lately??
You have the same paint scheme Betty Blue does. 1st time I've seen another like that. Cool. -
-
What's this dohicky
Sweet, make total sense now. Thanks Brother! @Bextreme04 -
What's this dohicky
Ah, ok. Lever is disconnected from diff since we're changing oil. So lifting it up obviously opens the valve... -
What's this dohicky
So, the rear brake line feed this dohicky that is attached to the rear diff. It then goes around to a t-fitting and feeds both rear drum cylinders. Reason I'm asking is I'm pushing denatured alcohol through to clean lines before attaching to new cylinders. We good men? Truthfully... -
Hello, my name is Derek, and I have Just joined this page, trying to find some good information on working on my new 1978 k30
Antenna might not be connected? Just one speaker? Welcome. Ditto to pic of truck.- Sgt Gus
- Post #7
- Forum: Introduction
-
What have you done to your square lately??
Finished the other drum. Replaced parts and painted. Bearing were good so just did inside seal like the other side. Draining diff today, then proportioning valve and hopefully bleed brakes so girl can drive. -
What new tools have you got lately?
I have a decent 3 ton jack from an estate auction. It lifted my Dad but not a truck. I have a new seal kit on the bench, haven't gotten to it. Borrowed the neighbors lol. -
72 Monte Carlo project
My 1st car was a 72 Monte. Still mis it!- Sgt Gus
- Post #11
- Forum: Other Vehicles
-
Wiring Two subs together?
I'd follow the read from @CountKrunk. We know you have two DVC subs, but what ohms? Seems like you're gonna want amp bridged mono and run subs in parallel if at 2ohms each. Don't just pick a diagram...- Sgt Gus
- Post #12
- Forum: Stereo & Entertainment Systems
-
Gas tank installation help please
I used a transmission jack, you could do like ricko1966 said though. I left my hoses long enough from the tank on the ground and coiled when it went up.- Sgt Gus
- Post #10
- Forum: Introduction
-
Wiring Two subs together?
https://images.app.goo.gl/8k4kKezmtkGPgbqT7 This is a visual. For me...less is more. If you want something musical, like a 4 Ohm set up. 1 ohm you are just gonna get you and your car rattled, especially the car 3 places from you. So all about what you're trying to accomplish.- Sgt Gus
- Post #9
- Forum: Stereo & Entertainment Systems
-
Wiring Two subs together?
https://images.app.goo.gl/yd6n25Gjrtbdexa8A Boom- Sgt Gus
- Post #6
- Forum: Stereo & Entertainment Systems
-
1987 454 TBI stalls at idle after a short time
Sweet burb. Horse trailering is one big reason my daughter wanted her 87 pickup.- Sgt Gus
- Post #48
- Forum: Tech Discussion
-
What have you done to your square lately??
Other funny part was that I had measured and moved truck over twice. I clearly measured from the wrong spot with tire on. -
What have you done to your square lately??
I looked at our truck and am not sure what the hole's look like, but you can get various sizes of aluminum plug buttons at the hardware store. Put some pooky around it if you need to keep water out. But for you, welding may be better choice. -
What have you done to your square lately??
Probably keep more of the mud off you, and assume you can still roll up a window even. Keep ya from getting your hair messy. Looks good! -
What have you done to your square lately??
I thought this was humorous. I didn't panic (mostly). For those who have a garage or shop NOT full of stuff. Pics are in order of, 1) final result 2) Issue, you see it? 3) plan 4) Yay! Had to giggle internet to figure out how to remove drawer. Two screws, sh!t in the way...drill with 90°...
