Search results

  1. Jppr26

    Wiper arm removal… Don’t laugh!

    You get it off yet? Mine I put a chunk of wood down beside the stem then used a pry bar. My Chilton manual says to lift on the wiper arm then pry it off the post.
  2. Jppr26

    Coolant wtff?

    So I have the new cap on and it fits a lot looser, the rubber on my old cap was swollen and creating too much resistance for the cap to vent properly I believe, the temp gage dose jump around a bit still, but I am still running straight water flushing the system. It also don’t help that I’m only...
  3. Jppr26

    Need help. Nothing works

    Battery ain’t hooked up. Sorry couldn’t help myself
  4. Jppr26

    Need help. Nothing works

    I know exactly what it is now. If you look at the picture you can find it.
  5. Jppr26

    Need help. Nothing works

    Use the red wire coming off your pump relay harness your ignition must be off that wire is a test/prime wire to see if your pump works
  6. Jppr26

    Coolant wtff?

    The seal on my old cap was tight going into the new radiator, my thinking was that it took too much pressure to push it, the truck never got above 210°, but I have noticed that it still fluctuates between 155° and 210°, I’m thinking about getting a lower temp thermostat, it has a new stock temp...
  7. Jppr26

    Coolant wtff?

    So I’ve replaced everything but the hoses on my 87 v20 sb350 cooling System hopefully this was the last issue. Recently replaced the radiator because mine was missing a lot of fins, my new radiator was the HD above stock other than that, nothing special, let it run and get hot added water as...
  8. Jppr26

    Fluctuating temp gage

    Have a shroud, stock 3 blade fan, and clutch
  9. Jppr26

    Fluctuating temp gage

    Next...figure out why the new sending unit on the left side ain’t working, I’ve replaced everything I can find to make it work again, it was working fine after I replaced it, then one day just up and shat the bed. I’m gong to pull the bed and check wiring and function
  10. Jppr26

    Fluctuating temp gage

    Well got the new radiator in yesterday, and took it for a drive, the truck ran around 155° on the gage and about 185° when I was running it hard. Before it would run at around 185° and if I got on it it would jump to about 220° then calm down after a bit
  11. Jppr26

    Fluctuating temp gage

    What can I say other than coastal trucks can suck, your money that is
  12. Jppr26

    Fluctuating temp gage

  13. Jppr26

    Fluctuating temp gage

    Ok how do I add a photo? It’s worse then I thought probably a third of the cooling fins were gone
  14. Jppr26

    Fluctuating temp gage

    So I looked at the fan side of my radiator and this is what I found
  15. Jppr26

    Tailgate Handle Assembly

    The return spring works off the latch springs, I tried like hell to get mine apart but just ended up stripping the 3 Phillips head screws out and said f-it. Sprayed it with wd40 for a few days then worked the latch and had to reach in with a punch to set it back a few times, if you got slop you...
  16. Jppr26

    Fluctuating temp gage

    When I said crusty I meant it’s in bad shape, missing patches of fins between the tubes and some mushed in, I’ll replace it befor I have it cleaned out. Fan clutch seems good has resistance
  17. Jppr26

    Fluctuating temp gage

    So I’ve been driving my 87’ v20 with a 350 motor for about two months now and I’ve noticed that whenever I accelerate, drive slow, or drop a gear to pull even a small hill my temp gage climes to the 210°-220° mark then it drops back down. I have installed a new water pump, t-stat, and coolant...
  18. Jppr26

    Blinker issues “SOLVED”

    It was kinda easy not much on the YouTube that I found, there is a turn signal switch video or two but nothing 100%. You will need a steering wheel puller, and a lock plate compressor, philips, few torques, and 3 different sockets to remove the column/dash mount, and steering wheel nut, both...
  19. Jppr26

    Blinker issues “SOLVED”

    So it turns out it was the blinker switch in the column, it went in easier than I thought it would, turns out the reassemble was a bit more of a pain, mainly when you realize you missed a piece, and then another, and have to take the column apart 2 extra times. But it all works as it should
  20. Jppr26

    Blinker issues “SOLVED”

    I’m suspecting my multi switch in the column I pulled it out and was going to bench test it but I don’t know what wire is the common ground/hot, I guse I could just run through them all and what ever one is the most constant is the one I’m looking for, right?? I suck at this wiring thing
  21. Jppr26

    Blinker issues “SOLVED”

    Yes, it is a new bulb, and I even switched it with the one from the left side that works as it should and the left works fine with the new bulb, and the old
  22. Jppr26

    Blinker issues “SOLVED”

    So far all my running lights work perfectly, my front right dose not blink all the other lights work as they should, the front right won’t even flash when I turn on the hazard lights
  23. Jppr26

    Blinker issues “SOLVED”

    The side marker light wires were chewed off from a mouse or squirrel and has been replaced and works, I think the front and rear lights are switched individually along with the dash indicator light
  24. Jppr26

    Blinker issues “SOLVED”

    As far as I know the only thing on the blinker system is the, bulbs, sockets, wires, 1 relay, 1 fuse, and the switch. The only thing original is the wires, and the blinker switch. Am I missing something in the blinker system??? If so I have no idea what it is
  25. Jppr26

    Blinker issues “SOLVED”

    Well I’m going to pull the steering column apart tomorrow and see if the switch is bad I used a light probe on the dark blue wire at the harness coming through the bottom of the column, if I was correct I should of had power there, but didn’t

Latest posts

Forum statistics

Threads
45,586
Posts
986,944
Members
38,675
Latest member
Shak379
Top