Search results

  1. Wilfred

    '84 bedside sheet steel stock gauge?

    Ordering new "OEM" replacement bedsides. Wondering what the stock thickness is? 16 ga.? 18 ga.?
  2. Wilfred

    While replacing the front main seal i should.....

    This one looks pretty good https://www.jegs.com/i/JEGS/555/81395/10002/-1
  3. Wilfred

    While replacing the front main seal i should.....

    Its not even in stock at summit, I would have to wait till like September.... LMAO I dont trust Jeggs as far as I can throw em - this motor from them is only 5 years old and already a leaking front main... Whats a good harmonic balance puller?
  4. Wilfred

    While replacing the front main seal i should.....

    Just found a slow leak in the front main seal and so im thinking while im in there Ive got options to do other stuff too what do yall think? I wonder about upgrading to a one piece seal (if in fact I have a two piece)....
  5. Wilfred

    10 bolt 8.5" corporate front axle U joint part #

    Anybody got the spicer part number...? I seem to have missplaced it.
  6. Wilfred

    Getting rid of old gas

    Any ideas besides burning it?
  7. Wilfred

    Stumbled a little for a quarter mile or a half mile while giving it a little throttle going 45mph

    Right, or suck something further into where it doesnt belong! Thanks for al the info!
  8. Wilfred

    SM465 Chatters when I get on it.

    What about the GL1? Ive been using valvoline 80W90
  9. Wilfred

    SM465 Chatters when I get on it.

    Can it be used in the differentials too? Is this the stuff?
  10. Wilfred

    Stumbled a little for a quarter mile or a half mile while giving it a little throttle going 45mph

    I like the plugs and wires idea. The distributor is as old as the engine (5 years). Take a look at the inside of the fuel filter, attached. I just replaced it and am going to try firing it up. Might clean out the gas tank when I replace the sheet metal in the rear end.
  11. Wilfred

    SM465 Chatters when I get on it.

    80W90
  12. Wilfred

    Stumbled a little for a quarter mile or a half mile while giving it a little throttle going 45mph

    5 year old 350 engine, 10 year old 1406 edelbrock I have rebuilt a couple times. Fuel pump is a couple years old. I think it might be a vacuum leak but I did just adjust the choke to the front of the truck considerably (eighth or a quarter turn) because I am fed up with the fast idle slipping...
  13. Wilfred

    Fuel pump pushrod won’t slide into block

    I know its a difficult spot to get a good picture of what that material is exactly... Its 99.999% something you could get out if you spent a day whittling down an easy out to get it all the way down to it and gently heating up the outside of the block with a butane torch I betcha would work...
  14. Wilfred

    SM465 Chatters when I get on it.

    This is definitely the transmission chattering. I "recently" replacing the original 700R4 with my covid SM 465 transmission as a set with an NP 205 and adapter (but no power sleeve) that I got cheap from this kid who said he rebuilt it and it works well enough. I got a power sleeve from company...
  15. Wilfred

    really need the experts on this, runs beautiful won't move

    Could be a bad shifter
  16. Wilfred

    NP 205 front output shaft gears slightly different?

    Yes, both 1.75"
  17. Wilfred

    NP 205 front output shaft gears slightly different?

    My two front output shafts are slightly different and I am curious the reason. There is an extra groove in the gear on the 10 spline vs the 30 spline. See pic. Any ideas?
  18. Wilfred

    Wipers barley working

    A common place to find this ground and a few others is connected to the top of the parking brake assembly. See photo below. There is a ground block with 6 prongs for various wires to plug into. With the age of these trucks, the mounting hardware of the parking break pedal will corrode and...
  19. Wilfred

    Front axle off set to passenger side

    Are you missing a top leaf? Looks like the keepers got some room to take another in the first series of pics from 3-8-22
  20. Wilfred

    Correct NP205 front output for '84 blazer

    You are right though. I am going to probably put the 32 spline in the old case and rebuild it. Thanks for the suggestion!
  21. Wilfred

    Correct NP205 front output for '84 blazer

    In your opinion it is "the best". If my plan was to put 45"+ tires on her down the road it would probably be my opinion too.
  22. Wilfred

    Correct NP205 front output for '84 blazer

    Anymore spacers* FTFY Just another good reason to leave the stock 30 spline. What is 30 spline good up to 40" tires and 800 #-ft? Doubt Ill change it but that does sound cool!
  23. Wilfred

    Correct NP205 front output for '84 blazer

    Might as well just go with a ford 9" rear and be done with it HAHA! I wonder how much room there is with the bigger CV over the cross member. Might have to shorten her a bit if I'm going to go with something bigger. Maybe spacers between the frame/cross member and cross member/transmission...
  24. Wilfred

    Correct NP205 front output for '84 blazer

    I purchased a very nicely rebuild transfer case from ***** transmission company. Everything looks great except for the front output. They sold me a 1.125" diameter 10 spline front output. The invoice says 78 - 84 10SPLinput but no mention of the output shafts. My quick youtube wikipedia...
  25. Wilfred

    SM465 to np205 clack-a-lackin when I get on it

    I shattered one last year came out in 6 different pieces

Latest posts

Forum statistics

Threads
45,583
Posts
986,860
Members
38,672
Latest member
Knightewulf
Top