Search results

  1. bigcountryguy19

    Wobble wobble wobble, rear axle.

    Sounds like death wobble to me, check all your front ball joints, tie rod ends, shocks and steering stabilizer. Do you have a two piece rear driveshaft? If so check the carrier bearing, I have had those cause horrible vibrations also. Does it feel like the whole truck is hopping when the wobble...
  2. bigcountryguy19

    NO OIL pressure

    No, a loose pan will not make the pickup pull in air, unless it's so loose it's hanging off the bottom of the engine by one bolt lol. While you have the pan off put a new oil pump and driverod sleeve in, you can get them for 25 to 50 bucks. Sent from my iPhone using Tapatalk
  3. bigcountryguy19

    Squarebody Differentials.

    Squarebody Differnetials. Count the teeth on the ring gear, and the pinion, devide the two and walah lol Sent from my iPhone using Tapatalk
  4. bigcountryguy19

    Steering arm removal

    Get a brass drift punch and smack the arm from the top, be carefully not to hit the studs, soaking and some heat will help also. We have same type of washers on the forklift wheels, this is how I usually get them loose. Sent from my iPhone using Tapatalk
  5. bigcountryguy19

    hello from south east wisconsin

    Welcome to the forum Sent from my iPhone using Tapatalk
  6. bigcountryguy19

    Bad Fuel Tank Selector Valve?

    Rock auto has them for right around 50 bucks, I just checked. It's were I ordered mine from. Sent from my iPhone using Tapatalk
  7. bigcountryguy19

    Show me your 8 lug wheels!

    They are few and far between, I would love to have a set also. I haven't come across any in years. They just have a great nostalgic look to them. Sent from my iPhone using Tapatalk
  8. bigcountryguy19

    How To Refurbish Your Dashpad

    I'm sure someone with more money than sense will buy it lol Sent from my iPhone using Tapatalk
  9. bigcountryguy19

    Squarebody Differentials.

    Squarebody Differnetials. Ok, thanks y'all. I think my parts truck is a 87 with a mid 70s frame. Just wanted to see if it was a 44 in the front. Sent from my iPhone using Tapatalk
  10. bigcountryguy19

    np208c 1

    You will have to change the input shaft. The spline count is different. Maybe you can salvage it out of your old case. Unless they changed something in the later years. Count the splines to be sure Sent from my iPhone using Tapatalk
  11. bigcountryguy19

    Ignition Issues

    Could be the ignition switch on the column going bad, or something is wrong with the linkage. Sent from my iPhone using Tapatalk
  12. bigcountryguy19

    Squarebody Differentials.

    How can you tell a Dana 44 front axle and a corporate 10 bolt apart? Do they look different or just with numbers on the case?
  13. bigcountryguy19

    6x6

    I bet that thing screams with that two stroke Detroit. Sent from my iPhone using Tapatalk
  14. bigcountryguy19

    will buy new tires, need suggestions

    I have got Goodyear duratracs on my k20. They work great, on and off road. For four 305 70 16 it was 1300 Sent from my iPhone using Tapatalk
  15. bigcountryguy19

    SOLD NOS GM door panels

    NOS GM door panels I would take them, but I'm a little low on funds right now. They are exactly what I need. Sent from my iPhone using Tapatalk
  16. bigcountryguy19

    New Girl

    Welcome! That's one sweet truck right there. Sent from my iPhone using Tapatalk
  17. bigcountryguy19

    Ground wire issues?

    Please disregard my last statement, I missed the part where you already changed it, sorry. Sent from my iPhone using Tapatalk
  18. bigcountryguy19

    Ground wire issues?

    Sounds like it's starving for fuel, could the filter be plugged? It would be an easy thing to check. It might have good pressure at idle, then as you accelerate the filter is restricting flow. Sent from my iPhone using Tapatalk
  19. bigcountryguy19

    2-2.5" Lift Kits?

    I have a rough country 2" lift on my 84. Its not bad, its a tad stiff in the front but thats all. It came with 2" blocks for the rear and i have had no trouble out of any of it. Only thing i recommend is try not to use thier brake line relocators, they are junk. but if you already have a 4" on...
  20. bigcountryguy19

    Carburetor rebuild

    Personally, I would throw that carb in the nearest river lol, but that's just me, I like holleys Sent from my iPhone using Tapatalk
  21. bigcountryguy19

    6x6

    Stacey David showcased one on gearz Sent from my iPhone using Tapatalk
  22. bigcountryguy19

    6x6

    It is split in the middle, it's basically like a truck and trailer, bit the trailer axle is driven also. Sent from my iPhone using Tapatalk
  23. bigcountryguy19

    8.1L/4L80E swap into 84 Dually

    I had this problem with my headlights on my 84, turns out that the spades on the lights were corroded, cleaned them and put dialectric grease on them and problem went away. Sent from my iPhone using Tapatalk
  24. bigcountryguy19

    Welding spider gears?

    Just give it a try and let us know how it works lol, If it works good I will do it to mine too. Sent from my iPhone using Tapatalk
  25. bigcountryguy19

    77 3/4 Ton Lift question??

    How high are you going to lift it? IIRC driveshafts should be ok up to 6". And at 6" some lower the transfer case a bit to help with driveline angle. Shouldn't be any differant than lifting a non full time truck. Just make shure all tires are the same size, which I'm sure u know already. The...

Latest posts

Forum statistics

Threads
45,581
Posts
986,840
Members
38,672
Latest member
Knightewulf
Top