Search results

  1. eskimomann209

    208 the same as 203 or 205

    Rusty you beg for help , dont mention what transmission your np208 is coming from and get mad when someone doesn’t give you a 45 minute education on everything you need to know about transfer case generations and applications. And here is a perfect example of you running your mouth The adapter...
  2. eskimomann209

    208 the same as 203 or 205

    The 208 was also behind the 350s in the early 80s
  3. eskimomann209

    208 the same as 203 or 205

    You come off kinda rude, that’s why people ignore you. welcome to the internet. :33: Muahaha. They will bolt up, depending on the adapter. Round face vs the figure 8 mount. What do you have. And what are you actually trying to do? Your question is very incomplete. you have a round faced 208...
  4. eskimomann209

    Air horn came in yesterday

    Under the dash it’s a black ground wire. under the hood it’s a green wire. depending on where you tap in depends where on that relay you’ll want to wire it
  5. eskimomann209

    Oil pressure gauge question

    Like what you see with the brake lines by the master. Coil it up a few turns on the firewall before heading into the cab. I too prefer the electric senders. It’s what I have in my truck. It was surprisingly annoying getting the correct one from the parts store. I pretty much had to look it up...
  6. eskimomann209

    1984 Headliner

    Just go get fabric from the fabric store! Use a brush to dust off the old powdery foam and use some headliner spray. It’ll work great.
  7. eskimomann209

    How... do you build a stepside?

    Bolt lengths are different from the fleet side bed as well. I’m sure most would work but I’m told a couple were the wrong length. Got my stainless steel bolt kit off a kid with a step side. He said they didn’t work for him due to it being a stepper.
  8. eskimomann209

    1981-1987 Silverado 10 Fender Emblems

    Use NOS 3m double sided tape
  9. eskimomann209

    Core plugs.... rtv or dry?

    I have seen them rubber plugs last for years. I put one in a buddy’s truck 10 years ago and he never came back to have me change it for the right one. It weeps tho. I can see the water stain under it. I do brass with no sealant. But I wouldn’t turn it away if I had some no2 form a gasket. I just...
  10. eskimomann209

    86 K10 5.3 swap

    Some people get away with using the 6.5 gmt400 pedals. I think it might be in this thread. my trucks pretty low and I don’t have clearance issues. With the ground or any crossmembers.
  11. eskimomann209

    86 K10 5.3 swap

    They say the speedo is always a little off. Factored in to keep people from speeding.
  12. eskimomann209

    Is the water pump toast?

    1/2 the job was done before you started!
  13. eskimomann209

    Is the water pump toast?

    That’s the weep hole. When it leaks there it’s time for a new one. It’s an indicator. Sometimes even new ones leak from there a bit. But they tend to seal up. If yours was sitting I’d swap it. Is it a newer one? it looks clean. Might be worth it to wait a bit. But I had some replacements that...
  14. eskimomann209

    What would you pay for a nv4500 trans with use and wear, but functional when pulled

    Driveline ( if that’s what you’re worried about) should clear the bell housing then.
  15. eskimomann209

    What would you pay for a nv4500 trans with use and wear, but functional when pulled

    truck lifted?
  16. eskimomann209

    What would you pay for a nv4500 trans with use and wear, but functional when pulled

    Early 90s chevys have a lower first gear. I think In 94 it goes higher. And dodge is the one with the nut that slips off and you lose OD.
  17. eskimomann209

    What would you pay for a nv4500 trans with use and wear, but functional when pulled

    Ahh I see. I have done the swaps in the later square bodies. They had the hydraulic setup in them. I assumed (incorrectly) you guys were worried about bolt Patterns. I think it’s 85+ trucks are already hydro. Another alternative is to drill the nv4500 to accept your linkage bell housing from...
  18. eskimomann209

    Brake warning light - what does it do

    I start plenty of threads. I also don’t feel ignored on any questions I post. And I’m not specifically attempting to “piggyback” on HER threads. I add info or bump threads with related questions I may have to increase views of her or others threads as well. Don’t like it? Welcome to the...
View older results

Latest posts

Forum statistics

Threads
45,567
Posts
986,424
Members
38,656
Latest member
Corncob
Top