Search results

  1. eskimomann209

    Bed floor rubber mat

    why lube a bed mat?
  2. eskimomann209

    What color is this Green? I need some help

    He has the right of it. They set it on there and find the match. And will give you the generation / year it was used. That’s how I matched my color on my Truck ( wasn’t a GM color when I got it ) And it is SPOT on
  3. eskimomann209

    Warped drums

    Got the shoes on right? There’s a front shoe and a back shoe. One has a larger contact area than the other. i THINK the larger one goes toward the rear of the truck. But it’s been a while. you also gotta lube the contact points of the shoes to the backing plate so they can slip back. post...
  4. eskimomann209

    Warped drums

    Sounds like you’re setting them too tight. But honestly, I’m having a hard time understanding your writing. If a drum is turned it’s no longer warped. That’s the point of turning. If you have new drums, freshly turned and the problem persists. You have a different problem.
  5. eskimomann209

    Bed floor rubber mat

    This one is for a square. But it’s a long bed? Would it be as simple as cutting the area closest to the tail gate?
  6. eskimomann209

    Bed floor rubber mat

    What does the silicone do
  7. eskimomann209

    Anyone running wipers bigger than 16" oem?

    Yeah but you’re a Rebel that runs atf in the steering pump;)
  8. eskimomann209

    Driver Side Alternator?

    If the hole isn’t needed. I’d tap it to whatever the next size is and put some blue form a gasket on a short bolt and sinch it down. Let it set up for 12 hours fill her and run it. plenty of bolts and plugs done this way.
  9. eskimomann209

    Full Suspension Rebuild Parts List

    This can get crazy few variations over the years d44 hubs had small and large bearings, tREs and drag link changed a bit over the years too. you mention bearings so I mentioned axles but one could debate if it’s “suspension work.” you want suspension , axle, and steering part #s?
  10. eskimomann209

    Giving rusty parts a smooth clean paintjob?

    I avoided mentioning por-15 Because I have not used it in a rattle can. Even though I have one on the garage shelf. Lol
  11. eskimomann209

    Cluster Refurb - What are options

    I don’t think they’re doing it anymore
  12. eskimomann209

    Window issues

    I too would try the lube move. But it’s not uncommon for these motors to give up the ghost. I’d do the relay mod to get more power to them AND swap motors. They get so abused with the low power setup they had. All the strain goes on the motor. I swapped the motor on my driver side and installed...
  13. eskimomann209

    Giving rusty parts a smooth clean paintjob?

    A cup brush for the angle grinders. Won’t get rid of pitting tho. There isn’t really a solution for that. Besides filling it In one way or another. Wear Saftey glasses with these, doesn’t matter how cool you are. These things do damage. You’ll find wire in your underwear later if doing it in...
  14. eskimomann209

    Original GM rocker panels

    Guys asking 150 for the set.
  15. eskimomann209

    live and learn AGAIN (Brakes)

    Gummed up and bad tolerance are two totally different issues. If it was a bad tolerance a little cleaning isn’t going to fix anything. my guess is your lines were dirty and you sent some shit into the cylinder. Rubber line at the T breaks down sometimes and brake line rust is notorious in...
  16. eskimomann209

    What's a 93 Chevy 4x4 Stepside short box worth ?

    Those are the same prices roughly for California in the Central Valley. Anywhere from 900 for a runner all the way up to 5k for a clean example. steppers are slower to sell but the picture is important.
  17. eskimomann209

    '79 Camaro Restomod

    Your tire looks wire thin! Super low profile. Seriously tho. Looks like a tight squeeze. Gunna look nice in there.
  18. eskimomann209

    What have you done to your square lately??

    Why the seasonal hood?
  19. eskimomann209

    Double Din Radio

    I hear ya. But the dash cages are a dime a dozen at my pick n pull. If I wanted one like that I’d do it. I personally prefer the motorized flip outs. I like the way mine covers the ac controls when not in use. provides all the info I need while driving.
  20. eskimomann209

    What have you done to your square lately??

    Those look sexy. Mine uses the stock xmember. It’s causes my exhaust to drop below the frame in that spot but the rest is nice n tucked. But I really wish I spent the money and bought one.
  21. eskimomann209

    What have you done to your square lately??

    Agreed it would look a lot better contoured. But it is well hidden under there.
  22. eskimomann209

    What have you done to your square lately??

    That looks good. Double sheer, grade 8 , edges broken... fine craftsmanship sir.
  23. eskimomann209

    What have you done to your square lately??

    Added a light up bow tie. Needed a new one, figured why not a modern one?
  24. eskimomann209

    208 the same as 203 or 205

    I think he’d frown on spending the money to have the output shaft swapped but... now that I think about it. The factory 350/ 208s might have had the Longer output shaft (in the 350) any ways. It’s hard to remember without the parts here for measurements. I agree it might be better to give this...
  25. eskimomann209

    208 the same as 203 or 205

    Sorry for your shitty day Rusty. If you have the np208 and a 350. Get the adapter for the th350 to np208. There were a few np205/ being used until like 83 or 84 (later in some HD applications ). So make sure it’s a 208. Your local JY should have them relatively inexpensive. The 700r4 one will...

Latest posts

Forum statistics

Threads
45,570
Posts
986,494
Members
38,661
Latest member
Todd Lemon
Top