Search results

  1. eskimomann209

    body mounts...rubber or polyurethane?

    I have a squeak. I feel like it’s my tailgate. But with the exhaust and 2 12s hitting I don’t notice a squeak most days lol.
  2. eskimomann209

    body mounts...rubber or polyurethane?

    The Ploy last forever, but the rubber “feel” better. They have some bounce when driving.
  3. eskimomann209

    Leaf Spring hangers- Where to buy?

    I made a set of hangers for a shackle flip. Ran em a few years and then went 4 link. It’s not that hard to make em. I’m sure your buddy can do it no problem.
  4. eskimomann209

    SM465 fluid - i used gear lube, maybe synthetic gear lube - what now

    LMFAO. Even shops fuck this one up. OP, If you followed the manual I think you should be alright. The argument vs synthetic and non synthetic gets tiresome. Some even label their stuff as synthetic and it isn’t. If it’s running and isn’t making a ton of scary noises, I’d run it.
  5. eskimomann209

    Preferred location for battery ground

    That’s exactly what I do @Catbox. mine have never corroded or failed me either. I even run dual setups with my crimped and soldered ends. Little bit o heat shrink and it looks professional. I even used colored heat shrink to make it look a little nicer on the positive sides. I’d be lying if I...
  6. eskimomann209

    Posi screws in your Square

    I used a lot of Robertson screws doing hardi backer cement board and other sub flooring stuff. I thought I loved those, then everyone went t25 Torx. I’ll admit for construction screws they’re the shit. I adore them, they also put a little flute on the tip of the screws to help cut better. Makes...
  7. eskimomann209

    LS Swap adding OEM cruise control

    Probably hit the AC relay wire lol. Close to it indeed.
  8. eskimomann209

    Little tip on trans installs. No trans jack.

    Good tip sir.
  9. eskimomann209

    LS & Vortec Swap to 90-91 VSS Electronic Gauge Cluster

    I used mine from the GMC Ventura. Swapped the face plate and needle over. But the back looked more like the square body one. It didn’t have the circuit board exposed.
  10. eskimomann209

    LS Swap adding OEM cruise control

    Mine is cable driven and she works. what switch are you using? some switches have the signals wrong and need relays to change em
  11. eskimomann209

    She's got the shakes, need help locating the cause.

    That’s Rusty. He’s a fast talking SOB. I hear his voice like an old Jazz bar poet reader dissing the Government. ( with background people snapping their fingers and hissing. )But overall he’s alright. But can get hard to follow. HOWEVER, pics of the project is considered legal tender here. You...
  12. eskimomann209

    She's got the shakes, need help locating the cause.

    I went that route because it’s fast cheap and easy. He also seems limited on abilities at the moment. He also mentioned it running better for a few days after putting in the autolites. Hopefully he can diagnose correctly and report back.
  13. eskimomann209

    She's got the shakes, need help locating the cause.

    Lmfao, after actually reading his post I feel like it’s everything except the head. I think burnt valve and bad rings. I also read that he swapped the plugs and it ran for a day or two. Making me think that originally oily plug is oily again. I’d swap that one out and see if she shapes up...
  14. eskimomann209

    She's got the shakes, need help locating the cause.

    I’m saying bad u joint or loose mount but I’m in the boat of way too long didn’t read. I always say don’t tell me a story, tell me what’s wrong. So we can fix it and move on. The clunk when shifting from one direction to another makes me think it’s somewhere IN or NEAR the driveline. Could be...
  15. eskimomann209

    Floor pan or patch?

    If it were me, I’d cut them all out and redo. Floor, inner and outer rockers.
  16. eskimomann209

    90-91 gauge cluster

    I have got two of these. I stock up on these and the pass drop 241s whenever I see em
  17. eskimomann209

    Excess Rear End Backlash

    4.10 gears depending on the axle and previous gears, there’s a carrier break that the PO might have ignored. It’s possible to get it close but it’ll never be right. Pics would be nice if the carrier and some measurements. I hate when someone else swaps new shit then sells. Makes me feel like...
  18. eskimomann209

    How to Identify a 700r4

    Lmfao. You called the Cummins junk? Early Detroit’s get way more shit than any gen of the Cummins engine. then turn around and talk about running common setups when you spend your whole life trying to go back to the “common” ( stock) setup? lol If someone lays 3 700s in front of you. One from a...
  19. eskimomann209

    LMC doors, good or bad?

    I’d say travel if you can. Maybe post in the wanted section how much you’ll be willing to pay for shipping. If not give LMC a shot their customer service is usually pretty good if there are issues.
  20. eskimomann209

    Fuel Filler Neck

    Year? Bed style? They’re formed hoses with part numbers. Check out lmc. I’d have posted them but I don’t have any info in your truck or bed mounted on your frame
  21. eskimomann209

    Got to a project I was putting off... Swapping to a tilt column

    Yeah my knees hit the hazard switch in my way in n out sometimes.
  22. eskimomann209

    10 bolt leaks but not where you would think

    Awesome. Glad it worked out for you.
  23. eskimomann209

    10 bolt leaks but not where you would think

    Well don’t leave me hanging. What did ya do?
  24. eskimomann209

    Let's see your GM squarebody stickers!

    I too, do not possess one of those nifty little stickers. *Sad face*
  25. eskimomann209

    Whats your hand soap?

    I dunno I have fast orange. I use that outside then go inside and finish up with Dawn. I do the prewash to keep the house sink from “looking dirty” or the wife will “ kill me.” :rolleyes:

Latest posts

Forum statistics

Threads
45,570
Posts
986,494
Members
38,661
Latest member
Todd Lemon
Top