Search results
-
1985 C10 Door Mirrors
My daughter was driving the 85 C10 today and collided with a 2008 Silverado and knocked the glass out of the 85 mirror and demolished the 08 mirror. The mirror on the 85 is the factory mirror is chrome metal. The only replacements I found so far are plastic. The housing has a dent, but I'm...- custodian
- Thread
- Replies: 17
- Forum: Glass & Mirrors
-
Cold Air intake
I bought another air box bottom to modify to run a flexible hose to the radiator support. Ill be filling in the original intake holes with a hard plastic. Should I use a 4" or 3" hose?- custodian
- Post #22
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
81-87 Front Clip on a 73
The main reason was to get the inside cab hood release. My granddaughter has been driving it and has found several occasions where someone had popped the hood and didn't get it closed all the way. After ready these post and trying to find what I can on the Internet, I've decide just to leave...- custodian
- Post #14
- Forum: Paint and Body
-
81-87 Front Clip on a 73
Have any idea how to make the 81 up hinges work on the 73?- custodian
- Post #5
- Forum: Paint and Body
-
81-87 Front Clip on a 73
I'm thinking about switching the 73 front clip top an 81-87 front clip. Other than switching the radiator support, what is involved in switching the hood hinges/supports?- custodian
- Thread
- Replies: 19
- Forum: Paint and Body
-
Correct way to measure width of a rim
What is the correct way to measure the width of a rim?- custodian
- Thread
- Replies: 1
- Forum: Wheels and Tires
-
Cold Air intake
I moved the battery to the drivers side.- custodian
- Post #21
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
Cold Air intake
This is my setup.- custodian
- Post #16
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
Cold Air intake
I'm taking you plugged most of the openings and it's drawing the air from the back side of the fender?- custodian
- Post #15
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
Cold Air intake
I've decided to keep the stock 5.3 Silverado air box. I'm going to modify the two air intake holes, one rectangle, one round, and run some flexible tubing down and make a scoop that would fit at the radiator support or under the radiator support.- custodian
- Post #12
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
Cold Air intake
I think the stock 5.3 throttle body is 78mm. Correct me if I'm wrong.- custodian
- Post #6
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
Cold Air intake
That cost more that my entire LS motor and trans.- custodian
- Post #5
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
FiTech Go EFI 4
Back up for sale. It ran good on the 350. I've removed the FiTech from the 85 to do an LS swap. -
Cold Air intake
Those that have done the LS swap, what would be a good cold air intake for the stock 5.3? I've tried one of those $60 sysytems from eBay and it was a sloppy fit. I'm currently using the stock air box and tubing system. My info is a stock 2002 Silverado 5.3 installed in the 73 C10.- custodian
- Thread
- Replies: 22
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
Rubber Blower Motor Hose
I'm looking for the rubber hose that goes from the blower motor to the heater/cooling housing or a place to get one. I need one for the 73 C10. -
AC Cover
The only thing I can think of is the diesel put out a lot of heat and it was a barrier. Who knows!- custodian
- Post #18
- Forum: Tech Discussion
-
6.2 to 350 swap
I did in the 85 C10. Removed everything 6.2, I cut out what wires that were not needed, used a few for power sources. I even removed the Hydroboost and replaced it with power vacuum brakes.- custodian
- Post #13
- Forum: Tech Discussion
-
AC Cover
Finally got around to replace the heater/AC fan. Took off the "cover" and this was what was under it.- custodian
- Post #16
- Forum: Tech Discussion
-
-
-
-
