Search results
-
What have you done to your square lately??
Morning session: I had some bubble wrap at the shop that was left over from a project so I was wondering how good it would look in the cab of my SB. Might provide minimal soundproofing and insulation, right? LOL. Started refreshing the grill. The inner sections are graphite peel-coat, and the... -
What have you done to your square lately??
I don't have a garage to work in so I would really like to finish it before the cold, wet, weather gets here. The drawback is the exhaust. This truck originally came with a Y-pipe connected to the headers, and a single muffler/exhaust pipe terminating back behind the driver's side rear tire... -
What have you done to your square lately??
Started getting the gauges and instrument panel ready to go. I wish the odometer was accessible so I can clean all the numbers. The circuit board should be here tomorrow. Started filling the '77 with cardboard from this project. Should be full by next weekend. . -
-
What have you done to your square lately??
I had to trim the entire front edge and the passenger side to get it to slide all the way in. I had to trim out both defrost heater grill openings to get the grill to sit down all the way. The floor mat took quite a while because it came with no shifter holes, and my old one came out in multiple... -
-
What have you done to your square lately??
Morning session: Installed the dash pad and of course it wouldn't fit. Had to trim quite a bit off with the razor knife. after that it went in fine. Finished running the speaker wires up to the radio location. Installed the floor mat and trim. Installed the shifter boot and TC shifter base. Boot... -
Fender badges
https://www.summitracing.com/parts/oam-9709/make/gmc/model/k2500/year/1985 -
Fender badges
Which Classic? https://www.classicparts.com/1981-87-Fender-Emblem-GMC-Sierra-Classic-1500-pr/productinfo/59%2D284/ -
What have you done to your square lately??
Worked on running new speaker wire to the rear speakers. Installed a new battery tray. Installed new springs in the ash tray. Tried installing the dash molding but the holes didn't line up and the molding was bigger than the cavity it goes in. Used a drill bit to line up the holes, and took the... -
What have you done to your square lately??
Well, the afternoon session didn't go so good. Noticed a leak at the tstat housing. I'll address it later. Started to replace the passenger side window and vent weather strip, and found the roller wheels on the regulator were stuck. Ordered a new set of regulators. Went to remove the ported... -
What have you done to your square lately??
Morning session: Glued down the floor liner and set the mat down. I won't make the mat permanent yet.Temporarily installed the rear speakers. -
What have you done to your square lately??
Before and after. Chrome before white any day. -
What have you done to your square lately??
Got a lot of parts delivered today. Installed the new tail light assemblies, mirrors, tstat, and tstat housing. The gauge lens showed up broken and the air filter showed up crushed. Cleaned and painted the air filter housing. -
What have you done to your square lately??
Got the stat housing and stat, door weather strip (installed immediately), vent window weather strip, floor liner and mat, belt weather strip for the windows. -
What have you done to your square lately??
Got the water pump, overflow tank, upper and lower radiator hoses, radiator cap, and new v-belts installed. -
'77 C10, Need Vin Plate Info Help
A'79 had a front GAWR of 3,250; a rear GAWR of 3,489; and a total GVWR of 6200. Yours is going to be pretty close to that.- CRM
- Post #6
- Forum: Tech Discussion
-
-
'77 C10, Need Vin Plate Info Help
Your registration paperwork should have it, as well as your insurance company.- CRM
- Post #3
- Forum: Tech Discussion
-
What have you done to your square lately??
Installed tail gate bumper stops and adjusted the catch assemblies. No more rattle and the hinges aren't catching against the body lip anymore. The PO definitely didn't know anything about repairs, or replacing things that were taken off. At least he kept everything in a box. I only have about... -
What have you done to your square lately??
I'm sure once I get it back on the road I'll find issues with the engine and drive line. I always told my kids "if you don't love it, don't buy it". -
What have you done to your square lately??
Installed new door striker bolts and reinstalled the drip rail molding over the doors. 26 items left on the to-do list. Currently at $2100 in purchases. -
Holley Sniper and Gas Tank Swap
You know this thread is hard to believe without pictures, right???- CRM
- Post #47
- Forum: TBI & EFI Conversions
-
What have you done to your square lately??
Decided to paint the gauge needles with fluorescent orange, and the interior of the mount with white. Makes everything easier to see, especially at night. -
What have you done to your square lately??
I used a wire wheel on the rust spots and treated them with rust treatment. After it dried, I put a coat of paint over the entire floor. Should receive the mat and sound liner this week.
