Search results

  1. C10MixMaster

    Carb line help. I'm so lost

    without a pic hard to say. but probably threaded port on the throttle plate brake booster and the smaller one is either for the unloader as mentioned or fresh air to the heated choke have to realize there were a lot of variations to these carbs pics help. your best bet is to use...
  2. C10MixMaster

    Carb line help. I'm so lost

    Best guess J EGR L PCV K EVAP canister purge H ported vacuum B ?
  3. C10MixMaster

    Factory Sway Bar Options

    the rears are rare as hens teeth on a c/k series , I've never seen one , might try to adapt one from an s10 series
  4. C10MixMaster

    Tuning for altitude

    http://www.bgsoflex.com/holley.html Holley jet correction calculator https://www.crankshaftcoalition.com/wiki/Reading_spark_plugs article on reading plugs I agree with rusty platinums dont belong in a sbc
  5. C10MixMaster

    Factory Sway Bar Options

    c10 sway bars are not that uncommon , no good reason to look at other donors
  6. C10MixMaster

    TH350 Slips in Drive but will back up

    Yes you need a rebuild the seal died sitting for that long. however you can try this, we have bought a couple extra years on a 4l60e with a reverse that was chattering. I usually dont go for the snake oil in a bottle but you have nothing left to loose..
  7. C10MixMaster

    Fuel Tank Question

    only 87 and up with TBI had baffles from the factory . As far as sending units OEM is almost always the best , not sure on the aftermarket ones
  8. C10MixMaster

    Looking at car lifts

    that scissor lift looks scary as hell (unstable) and there's no way you can pull a transmission or t case with it. I would go with the 2 post myself Used them for many years with no problems
  9. C10MixMaster

    700r4 Exploded !!!

    been there done that, broke 2 or 3 of input drums in my Camaro at the drag strip. the only other part that broke in that transmission was the spag , it let loose when the rear end grenaded and locked
  10. C10MixMaster

    Looking for a color code

    try this site you can find any color ever put on a car or truck and cross reference it to the major paint manufactures RPO etc. http://paintref.com/paintref/index.shtml
  11. C10MixMaster

    Steering column bearing help!

    https://www.ebay.com/itm/173670104498?epid=222750162&hash=item286f8b7db2:g:vhoAAOSwH55bUkJe
  12. C10MixMaster

    What have you done to your square lately??

    That's who I got mine from but went strait to the company cut fleabay / amazon out of there cut. and I added the crush sleeve eliminator to for an extra 15$ https://www.quickperformance.com/ and that was my stimulus splurge to.
  13. C10MixMaster

    What have you done to your square lately??

    opened up my new truetrac and 4.10 gears cant wait to get rid of the 3.07 peg leg
  14. C10MixMaster

    Fuel Pump Woes and Questions

    total brain fart, not sure how i did that , yes 18436572 :banghead: glad you guys caught that.
  15. C10MixMaster

    Fuel Pump Woes and Questions

    Qjets dont like a lot of pressure earlier ones carbs starting with a 70 only like around 5-6 psi .later ones with a carb number starting with 170 can take 7-8 psi. im running 9# with no problems but thats the upper limit. so pressure test and run a regulator if needed. before you pull...
  16. C10MixMaster

    New to this site. Looking for VIN decode info.

  17. C10MixMaster

    Coolant temp issues...

    I believe there are 2 coolant sensors on a CCC computer controlled carbureted engine , one for the gauge and one for the computer. 5K is way high for a gauge sensor. The 600 ohm is probably correct for your truck . Put the sender in the frig , grab a beer then your done with your beer...
  18. C10MixMaster

    Ring and pinion swap

    get an install kit there not that expensive ~ $70. you will need the shims / seal / crush sleeve / lock nut at the minimum. and if your going that far do the bearings and ring bolts to , which are all in the install kit. GM 12-Bolt rear diff UPGRADE: Positraction and gear swap | Hagerty...
  19. C10MixMaster

    Charcoal canister mystery hose.

    goes to ported vacuum on the carb.
  20. C10MixMaster

    truck is not sitting level - need help diagnosing

    I took my rear leaf springs apart and swapped leaves from side to side, alternating leaves with more of a curve with those with less of a curve . This took away most of the lean.
  21. C10MixMaster

    Correct carb app. for 1975 Blazer

    6300 puts it at heavy duty emissions. the 4th vin might only work on the trucks? or maybe the 4x4s already have a higher gvrw and didn't get the heavy half ton package? but at least you have figured out what you have..
  22. C10MixMaster

    Intake manifold leak

    defiantly an open hole to the lifter galley , pull the bolt clean it put some sealer on it put it back in and have a beer.
  23. C10MixMaster

    Correct carb app. for 1975 Blazer

    Actually there is a 1/2 ton option that was common called a heavy half ton or big 10 that are also heavy duty emissions with no cat and no egr. any truck 78 and before with a gwvr over 6000 is heavy duty. 1979 is a split year 6000 gvwr for feds is heavy duty in commifornia in 1979 it had to...
  24. C10MixMaster

    Power Windows Troubleshooting Info

    1) yes the breaker is the smaller of the two blue circles on the first pic. 2) yes the second pic is without the radio in the dash, and the relay is on the brake pedal bracket , you looking at the passenger side of the bracket about 2-3" behind the firewall..
  25. C10MixMaster

    Power Windows Troubleshooting Info

    ok early version used 5 wires 1977-1981? 1982? -1991 used 6 wires. 2 different systems . the early system grounds through the window motors ( put power to one terminal the window goes up and put power to the other it goes down) and the late system changes the polarity to the motors and...

Latest posts

Forum statistics

Threads
45,575
Posts
986,719
Members
38,665
Latest member
Dons79C10
Top