Search results
-
What have you done to your square lately??
@CalSgt thought about your mounting issues with the vintage air I cheated, had some 1/4 20 one inch bolts, spun them through the mounting plate and made them studs! Thanks for the heads up for the headache!! -
New wheels/tires - 73 K10 w/2” lift
my answer to @mrdap and @bbuse some trimming on the front will have to happen! But if the cancer I'm seeing on @bbuse I would take the wheel trim off first and let the tires remove the rust parts then clean it up! On a stock setup with a 2 inch lift should be ok!- hoagster
- Post #12
- Forum: Tech Discussion
-
LS swap
Need help finding a suitable sub for the electronic gas pedal any ideas- hoagster
- Post #46
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
Questions about turning a Burb into a 4 door pickup
Find an old long bed and use what you need! keep Them all period correct and be creative. 84 burb and 84 long bed etc.etc. I'm sure the frames are different but I don't think the different bends in the frame can't be overcome with shims or trimming. Not being a good welder or a very good... -
What have you done to your square lately??
Were did you source the parts? I know its the jeep mod! -
What have you done to your square lately??
got my firewall ready for A/C install, -
Steering box brace kits
Are you talking about these? this is a better picture, you can see this was a two piece kit. I also bought the inner frame stiffener from ORD. If you are going to lift it and run big tires I would fix that area right. this is the second truck I have had to do and the first on had to find a...- hoagster
- Post #5
- Forum: Lifted & Off-Road Systems
-
Firewall Cleanup : AC Install
Nevermind posting another picture I found it, I see you didn't follow their directions either which called out 2" and 1 1/8" holes!! The grommets would fall out! I'm glad I read and re-read the directions then pulled out the grommets and measured everything. I like your setup but I don't have...- hoagster
- Post #17
- Forum: Paint and Body
-
ISO speedo driven gear NP205
Until you find one, use your phone and google maps put a destination in it and start. It will give you the speed limit and your gps speed on the lower left corner of the screen.- hoagster
- Post #2
- Forum: Transfer Case
-
What size is my fuel tank?
Well thinking about your issue, I'll almost bet that either or both of your fuel hose's from the filler to the tank are done! I'm surprised the gas pump vent is allowing you to pump gas at all!- hoagster
- Post #17
- Forum: Carb Fuel Systems
-
Tailgate handle
L LMC is were I got it from! along with the other tailgate parts!- hoagster
- Post #15
- Forum: Paint and Body
-
What size is my fuel tank?
And you really don't need to know what size tank you have to calculate mpg! Just figure out how many miles you have driven since the last fill up then divide it by how many gallons you pump in since your last fillup.- hoagster
- Post #3
- Forum: Carb Fuel Systems
-
Tailgate handle
I'm pretty sure I got this one from AMD, maybe LMC I don't have the original handy but this one is beefy- hoagster
- Post #9
- Forum: Paint and Body
-
What have you done to your square lately??
Here's a link to the other style! https://www.amazon.com/Yukon-Gear-SP706529-Replacement-Differential -
What have you done to your square lately??
Compare the pictures first, there are two styles these are from a 73 K10 -
What have you done to your square lately??
I have a pair, I rebuilt my dana44 and replaced them, no pitting but you can see in the pictures they are used. Your welcome to them just reimburse me for the postage. -
Dumb question - what is this? (77 C10 350)
For that Ball, pm me your address I'll send it to you! it was 113 here yesterday so if it helps fix your A/C you can have it!- hoagster
- Post #8
- Forum: Tech Discussion
-
Dumb question - what is this? (77 C10 350)
I have one if anyone needs it. I'm not rebuilding my OEM A/C system.- hoagster
- Post #6
- Forum: Tech Discussion
-
What have you done to your square lately??
Started in on the cab, after this it will be wiring and firewall pad, haven't decided on the A/C yet OEM or other! Still need to work on the manual shifting but need to prep the cab first so I can install pedals and steering column. -
-
What have you done to your square lately??
W With the stock front OEM 3 leaf springs it rides just like every other Square little springier. Will see with the LS in it but the weight difference between motors isn't very much. -
What have you done to your square lately??
yea I have been running those load leveler Munroe's on all fours for a long time. -
What have you done to your square lately??
Cab is on the frame! As usual had a hurdle but nothing major. Back in the garage where all the parts are close by. shout out to ORD, Twin stick and zero cuts on the hump panel. Trying to figure out what to tackle next, guess we will see! Other pictures on the build! -
What have you done to your square lately??
Cab is going back on today! Got everything set up in the barn for the install. -
What have you done to your square lately??
Cleaned off a couple of years of dirt, Finished the fuel lines to the engine. Serviced the transmission, transfer case front and rear differentials with the proper gear lube. pulled out the profane body mounts for the cab, couple more things come to mind. But the cab is going back on!
