Search results

  1. Hunter79764

    AC Conversion Questions

    To my knowledge, all orifice tubes are "compatible" with 134, it's just a matter of what is the right size. If it's a single cab truck, in Wisconsin, I don't think you have a bad option, anything will work out ok, so probably just stock replacement, which I believe is white?
  2. Hunter79764

    AC Condenser - Should I use New Or Original.

    Newer microchannel condensers can reject a lot more heat than a fin and tube style, no myth or rumor to it. I was an engineer for Lennox HVAC on projects going from older to newer style, they certainly work. The question is, do you need it? Most single cab trucks will never notice the...
  3. Hunter79764

    Pro Flo 4 with Delphi FE0114 or ACDelco EP381

    Injectors are rated at a flow for a given pressure. Unless you go crazy extreme, any reasonable injector can run any reasonable pressure. Lowering the pressure into your 29lb/hr injectors will reduce the flow, giving longer injector cycles and I could see where the computer would have an easier...
  4. Hunter79764

    Pro Flo 4 with Delphi FE0114 or ACDelco EP381

    I read it as one of these guys under the hood right now, and he is looking to go with an 87 tank and fuel pump setup. https://www.summitracing.com/parts/edl-36032?seid=srese1&gclid=Cj0KCQiAsaS7BhDPARIsAAX5cSD2rB-Z6p02nMQFCso0P3DQmCxhYBj8u3QkcE5UwKYQtDyIYS54sNcaAvS7EALw_wcB If he has something...
  5. Hunter79764

    Pro Flo 4 with Delphi FE0114 or ACDelco EP381

    What about a Walbro? Genuine units are good, careful about buying on Amazon or something as the fakes are rampant. That said, I can't imagine either of the pumps listed wouldn't work for what you need. If you have the front tank kit, have you looked to see which pump is in there, and if it might...
  6. Hunter79764

    Shop heater

    I vote infrared electric if you use it intermittently. If you want to maintain a temperature for the entire day etc, you might actually look into a heat pump (you don't have to duct it, just have the "furnace" with a filter inlet and some sheetmetal scrap to direct the airflow where you are...
  7. Hunter79764

    Shop heater

    I use Texas for my shop heater... Jk, sort of. Not a huge need for it here, but I'm interested in adding a portable propane heater for mine next winter. Gas heat is usually more cost efficient to run, electric heat is usually more install friendly, but both of those depend on your utility...
  8. Hunter79764

    03 Trailblazer Build.

    That makes sense, just wanted to make sure you were accounting for that and didn't just forget to increase the fuel pressure or something. I'm following along and enjoying what you're doing, keep up the good work!
  9. Hunter79764

    03 Trailblazer Build.

    Just my ignorance showing, but is 43.5 the proper fuel pressure? I thought GM did 58 for most stuff of this vintage? If it is 43, that might be a cheap fix for maxed out injectors to swap in a 58 psi regulator (unless it's one that is regulated in the tank... ugh)
  10. Hunter79764

    1985 K2500 Build/LS Swap

    It's been a while since I've messed with it, but from memory, there's a few sets of instructions floating around out there, and/or you can ask someone who still does it currently, and it shouldn't be that hard to do. Of course, I could imagine in the current legal climate they might have pulled...
  11. Hunter79764

    350 or LS

    That's my take, but beware that the 4200 swap is not a fully baked option either, there will be trial and error and discovery along the way. The harness and electronics should be available from a few places (one is linked below), but the oil pan needs to be figured out, same for exhaust and...
  12. Hunter79764

    6.0 NV4500 K30 swap

    Pretty sure 241 came with both sides, but passenger drop is certainly less common. I think it was 88-91 Burbs and Crew Cabs, so small pool to draw from, but they do exist.
  13. Hunter79764

    Square-body?

    I love those types of stories, and now I'm motivated to leave my factory airbox alone... I've got a similar story that would take too long to type, but it involved some changes to an AC system I was an engineer on. I figured out some weird stuff that was going on and proposed a solution, they...
  14. Hunter79764

    6.0 NV4500 K30 swap

    My understanding is the NP208 and 241 are mostly the same, but 241 is updated. Think of it as 700R4 vs a 4L60E, a few update/improvements to go with the name change, but both are basically built for the same thing. Either would probably work fine in your truck if you don't beat on them, but...
  15. Hunter79764

    350 or LS

    My estimate on LS swaps used to be $2000 plus the cost of performance or maintenance parts, plus the cost of transmission but including a junkyard 5.3. That would at least get into the ballpark. Now, thanks to inflation etc, I think you should probably start at $2k plus your engine and...
  16. Hunter79764

    2001 Silverado advice

    Hey, if they already beat polio, why can't they can beat those cheating SOB's in your rec league?!?
  17. Hunter79764

    Mud Tires

    If you're a kid with a truck doing kid with a truck type stuff, it can chew through tires pretty quick and cost a fair amount. I have a set of remolded tires that I'm relatively happy with from these guys (Treadwright). My dad bought a set from Tire Recappers, and they seem to perform fine, but...
  18. Hunter79764

    Andi from Hannover/Germany with my 1985 C10 Stepside named "Daily-Blue1"

    Welcome! Nice truck, I still want a step side some day...
  19. Hunter79764

    2001 Silverado advice

    A few of my thoughts to echo others above, 300k isn't that tired, 250-350k is very common on these and I'll add my wife's 01 suburban 5.3 had crosshatch at 345k. At the same time, if you find a junkyard 4.8/5.3 (or even 6.0) and 4l60e combo with reasonable miles, pulling and reinstalling is not...
  20. Hunter79764

    1985 K2500 Build/LS Swap

    The other option I have used is LT1Swap, Brendan there is quick and good, he's been doing that service for years. It won't be a performance gain generally, but for a stock engine that just needs the toggles switched, and things like rear gear/tire size corrections, it's probably the easiest way...
  21. Hunter79764

    1985 K2500 Build/LS Swap

    Blackbear usually gets good marks (no personal experience), but if you're up for a small challenge to learn a new tool, picking up an HPTuners setup is probably a good option. Easy to fix those issues, and it is a great diagnostic tool if nothing else. It should just be 2 credits for you, and...
  22. Hunter79764

    Gun Rack Spacing

    Apples and oranges, but I'll throw in my setup, bought mine as a hunting truck suburban. Previous owner had installed 4 sets of racks, one on each rear side window at ~14" or 15" spacing. Also had an overhead 2 gun rack with velcro straps, but my favorite and most useful is the vertical mount...
  23. Hunter79764

    Square-body?

    For a fair amount of time, I was confused as the 90's style seemed to be more described as "square" based on design elements (door shapes, tail lights, grill shapes, etc) where 73-87 seemed to have generously rounded corners, but then if you look at a blank side profile, I suppose the overall...
  24. Hunter79764

    350 or LS

    I'm a fan of LS engines, but in this situation, I think you're best off with a rebuilt 350 and a carb, unless the tech school wants/needs to do something more modern, in which case a stock 5.3 or 6.0 (LS) is what you're after. Get the transmission that came behind it, have it rebuilt (if it's a...
  25. Hunter79764

    Wanting Led upgrade throughout while keeping stock look... Recommendations?

    RMS does seem to have good quality, and plenty of folks have been happy with them. And yes, the better LED's are getting much better about placing the LED element in the right place. Essentially the LED has to be the exact size and shape of an incandecent wire element to get the proper pattern...

Latest posts

Forum statistics

Threads
45,558
Posts
986,230
Members
38,644
Latest member
FenderBanger
Top