Search results

  1. Tyger13us

    Frame Repair Need Advice

    good write up........ that frame horn section came off a 3/4 ton gmc 4x4,,, its alot thicker, mated to a k10 frame... i guess thats why it looks funky to you,, but the section cut off fit right inside of it perfect,, 3/4 ton frames are a wee bit wider from lip to lip,, the only thing...
  2. Tyger13us

    Distributor Question

    HAHAHAHAHAHAHA,,, ROTFLMAO!!!!! yea,, if it was a race motor/street racer correctamundo.......... my last street racer motor i got 200k out of it,,, broken valve springs,, punched rockers,, burned up rocker balls," the groved ones"... back in the day,, my motor was a 327small journal...
  3. Tyger13us

    Frame Repair Need Advice

    factory specs....
  4. Tyger13us

    V-Dub Power

    i never got into anything after 66 model year,, the ball joint front end was weak,, then they went to strut and was junk,, i think 74 was the first year for the Super Beetle,it was front strut, it ran really good ether fuel injection or dual port heads and a Weber carb,, but the rest of the car...
  5. Tyger13us

    Distributor Question

    well,, that is right to prime it,, but to do it right ya need a dizzy housing for the cam journal/lifter gallery oiling,, with out it it just comes out the feed and dont feed the top end.. thats what the notch/ ringed groove is for at the bottom of the dizzy...... my machinist and i agree...
  6. Tyger13us

    Distributor Question

    yea,, i did,, but dont go full throttle,, easy it up,, at least i do to 5k rpm's than back down,, like HR said,, with the new rings and a good machine shop there seated @ 100 miles,, but i waited till i got 500,, dumped the oil and filter,, and refilled,, then 2 container of stp oil additive...
  7. Tyger13us

    New Process A833 4speed w/ OD MY6 MM7

    any diesel 6.5/6.2,, no matter what stick it had in it,, has a 12" clutch...that i know of anyway....... Un less ya live in farm land,, ya would be surprised what shit farmers do.. i got a 6.2 from out in the field from a farmer,, 6.2,, busted block where the starter bolts on and had a...
  8. Tyger13us

    Frame Repair Need Advice

    i didnt use a torch to cut,, it just dont get a straight line,, or alot of grinding afterwards.. i used a skill saw?!?! yep the saw ya cut lumber with and use a cutting disk,, ya can get 3 packs for cheap @ chinamart...... as far as the gap,, thats usually how its done,, but try not to get...
  9. Tyger13us

    V-Dub Power

    Thanks,, i wanted to get it running this summer,, but ya know how it goes.. my last BaJa bug got 48 mpg and this thing weighs nothing,, so i should get 60mpg,, if i can keep the front tires:big_banana_Dance: on the ground...
  10. Tyger13us

    Distributor Question

    X2 on that.. never let it idle for very long at any time till the cam is completely broke in,, the reason being is the squirter holes on the rods that throw oil up in to the cylinders also splash the cam as they go around,, so at an idle the oil aint making it to the cam,, and if ya think the...
  11. Tyger13us

    V-Dub Power

    Here ya go,, A Volkswagen thread....... another project of mine.. 62 pan king pin front swing in the rear.... this motor runs? but smokes like a train,, had a really lose belt and the dude i got it from smoked the motor..... its a 1500 with 1300 heads,, a real scab job... i have a...
  12. Tyger13us

    Frame Repair Need Advice

    X2.. On my truck,, it was so bad i had to cut the frame and weld a 3/4 ton frame horn section for the steering box........ i could have just cut a U section out and wraped it around the messed up part and did it that way? Getting it exact took alot of patients and measuring for the full...
  13. Tyger13us

    New Process A833 4speed w/ OD MY6 MM7

    "We were every which way but straight." Had a 64 nova ss and tacked it out in 3rd "th350",, with a ratchet shifter and went to down shift and it went straight to REVERSE!!!!!!! @ over 80 mph locked um up and WOOOOOOOOOOOOPIE hang on... busted the the big C clip out of the rear of the case...
  14. Tyger13us

    New Process A833 4speed w/ OD MY6 MM7

    It never slips then,, it slips the worst when your trying to get 10 tons of 2 ton hay bails rolling with a 6 wheel pintle hitch trailer and 3.08's.. its smokes the clutch,, once ya get it rolling there isn't any problems,, just dont stop to fast as it will push you all over the place and keep...
  15. Tyger13us

    New Process A833 4speed w/ OD MY6 MM7

    my diesel has a 12 inch clutch,, well,, 11 7/8 to be technical,, and come to find out that the pressure plate and clutch disc will bolt to 2 of my chevy truck flywheels........
  16. Tyger13us

    New Process A833 4speed w/ OD MY6 MM7

    I tryed.....
  17. Tyger13us

    New Process A833 4speed w/ OD MY6 MM7

    Got something for ya im sure ya will be interested in...... didnt know where else to put it...:favorites25: A present......
  18. Tyger13us

    New Process A833 4speed w/ OD MY6 MM7

    31x10.5x15's.. my k10 has 31x10.5x15 also and a th350 and 3.73's tacks the motor @3k rpm running 70 mph....it needs over drive so bad..... but my sbc's live @ 3k rpm and seem to like it,, but the mileage sucks..... if i could figure out a way to put this my6 in front of my 205 t...
  19. Tyger13us

    New Process A833 4speed w/ OD MY6 MM7

    oh yea,, the my6a833 aluminum trans thats in my truck is the strongest thats been in it,, except for the 465...... the gears,,IMO,, are to thin and to small in diameter in a muncie,, destroys the cluster gear... guess thats why they used the super t-10 behind BBC...Or th400.. but the 10...
  20. Tyger13us

    6.2L heads

    I got a set of free!! 6.2L heads,, i thought,, ok,, prolly cracked too.. nope,, ive got um tore down to cast iron and find a single crack anyplace....not even the pre chambers,, but the casting #'s are differnent on both heads,, but cant find a lick a difference in the heads.. so now there...
  21. Tyger13us

    Oldsmobile Engine Conversion

    So,, looks like the olds to chevy truck is on hold.......till spring..... jump on over to the 6.2L diesel thread so i dont get in trouble for going OT.....hahaha
  22. Tyger13us

    New Process A833 4speed w/ OD MY6 MM7

    here is somthing else strange? my mom has an 85 f 150,, well my truck really,, but it has a top load NP 4sp overdrive and it will bolt to the funky wide pattern bell housing that your cast iron mm7 bolts to!!! 27 spline out..... uses the same clutch disk as a 6 cyl gm........
  23. Tyger13us

    New Process A833 4speed w/ OD MY6 MM7

    Im the second owner,, 1982 c10 6.2L... i put a 465 in it but didnt want to put the factory 2.73's in it.... the 465 and the 308's were tacking the motor out doing 65......... so put the my6 back in after rebuilding it then blew up the rear end,, factory 3.08's... so i have a 72...
  24. Tyger13us

    New Process A833 4speed w/ OD MY6 MM7

    yea,, mine is 27,,350/700r4,, but im sure its just a shaft swap to 32...... gm did some weird shit with left over parts.......
  25. Tyger13us

    New Process A833 4speed w/ OD MY6 MM7

    on mine my trans bolts to this bell housing,, fist pic... i cant get a pic of the dr side exhaust is in the way.... but i have the multi bolt pattern bell housing also...... the way the tail shaft houseing bolt on is the same on the pass side... i tryed go get a pick of where the...

Latest posts

Forum statistics

Threads
45,567
Posts
986,424
Members
38,656
Latest member
Corncob
Top