Search results

  1. C

    What’s a tilt column worth?

    I gave $85.00 for an 84 manual shift tilt column last summer. With intermittent wipers and cruise.
  2. C

    Fender emblem removal

    I think the easiest way is to remove the fender. Holes on the back side to access the speed nuts for removal.
  3. C

    Lifting engine in place with carb studs?

    I've done it that way my self.
  4. C

    Tracing Thermostat wire Help

    No, that's not the oil pressure sender. It is at the back of the engine, driver side of the distributor. In the picture you have shows the temp sender for the temp gauge.
  5. C

    Cab swap help and pointers

    First make sure you have everything disconnected from the engine to the cab. All wires and grounds. Same goes for the tranny, make sure the boot is off so the shifter will clear the hump. you'll also have to take off fenders, inner and outer, plus the hood. there are 4 bolts under cab that hold...
  6. C

    New Member. Longtime Owner

  7. C

    Tail light woes

    Perseverance pays off yet again. Good job fella!:)
  8. C

    Grille Ataachment Screws

    Go to Ace Hardware. They have a pretty good selection of automotive fasteners.
  9. C

    Tail light woes

    I had the same problem. I attached a ground wire from the one inside the taillight housing to the frame and worked like a charm. Even cleaned up, the ground in the housing would not light my tail lights.
  10. C

    AuroraGirl is buying another square... is it a good one?

    You need to get off the dang computer and get that truck!!!
  11. C

    Howdy from Texas

    Welcome from Missouri. But, only my opinion, lowering a truck is the same as putting a lift kit on a Prius!
  12. C

    New member in MO

    Welcome from central Missouri!:welcome:
  13. C

    Storage tray behind the seat

    Where did you come by that one from? Looks sturdy.
  14. C

    New member-need advice on body panels

    Also try Craigslist. Squarebody parts pop up on there frequently.
  15. C

    New member-need advice on body panels

    If not there, you can try LMC, fixmyrust, carid, many more. Just plug Chevy repair panels into google and you'll see many options.
  16. C

    Storage tray behind the seat

    It's factory original. Sadly most haven't lasted as long as yours.
  17. C

    Fuse Block/Wiring Harness

    Should be pretty much identical.
  18. C

    Windshield washer pump troubleshooting and rebuild

    In an 86, the pump would be in the washer reservoir,
  19. C

    Transmission Options

    When did GM quit using the 292? Mid 80"s?
  20. C

    Want complete stock wiring harness for 83 C20

    I have one you can have for the ride. Just the interior side though.
  21. C

    Wanted: 1976 GMC Grill, AND 1976 GMC Tailgate

    Look at these: https://flint.craigslist.org/pts/d/gmc-chevy-square-body-grill-chevrolet/7128001485.html
  22. C

    1990 ChevyLight Duty 3/4 Ton

    A 3/4 ton with only 6 lugs?
  23. C

    No dash or tail lights, this is WEIRD !!!!!!!!!!!!!!!!!!!!!!!

    Go to the drivers tail light and remove the whole set up. there is a ground there that screws to the metal surounding the tail light assembly housing. Check to make sure that ground is good. Had the same problem and so ran a new ground wire and no more problem. Weird how it only effected the...
  24. C

    Valve cover bolts backing out on me - antiseize? lock washer?

    Can you peen a slight crown in the spread bar? That way it's putting down pressure on the valve cover while also putting up pressure on the bolt, there by acting like a lock washer.
  25. C

    Bench Seat slide adjsutment

    Try an Ace Hardware, they have a pretty good variety of springs.

Latest posts

Forum statistics

Threads
48,672
Posts
1,074,291
Members
43,344
Latest member
Original
Top