Search results

  1. Craig Nedrow

    14 Bolt 10.5" Rear Axle -FOUND-

    The C20 I have has a 9.5 ring gear, The K20 has the 10.5. Just my trucks, the C20 is a semi floater.
  2. Craig Nedrow

    I'm an old Motorhead

    Howdy brother....what engine and trans combo is that, Chrysler?
  3. Craig Nedrow

    K5 ls swap

    Thanks Hucked for this info, will use it on the Nova LS swap.
  4. Craig Nedrow

    What size/length/thread pitch bolts for brace on NP208 transfer case?

    If you have some calipers, just measure the hole dia, and then compair it to a tap drill chart. Don't have a tap drill chart? get on, everyone should have on, and a pair of calipers, saves time. From your friendly local machinist.
  5. Craig Nedrow

    Gear Ratio Help

    I would never swap from a OD trans to a 3hree speed, makes on since. My 489 cam duration is right at 300, 33" tire, 4:11 rear gear. It ran right @ 2800 to 3000 on the freeway with the 350, did fine, just made me tense and a bit noisy. The OD(4l80e) trans will help with that.
  6. Craig Nedrow

    VGG 1776 Clear vs Poppy’s Glossed Out Clear

    I bought two Milwaukee buffers, a small and a large. I wash often, wax about three or four times a year, and things look good. On the K20, just got the box painted, six base, three clear. Single stage works fine if you put it on thick enough so that it can be colorsanded, then keep it waxed...
  7. Craig Nedrow

    which bench seat is best? 75? 80? 81?

    obs4 truck seats should work, 90-98?
  8. Craig Nedrow

    Tube grille for 85, quad headlight type

    Have a tube grill on the 73, very difficult to get the hood open, not much room for fingers.
  9. Craig Nedrow

    M122 blown 5.3 in my 99 silveraydo

    Daang it, was so lovin' this thread then it stopped....You're a goer Vince, watching with interest...
  10. Craig Nedrow

    Windshield washer motor questions

    Thanks Bucket, I will check into it....
  11. Craig Nedrow

    To seal or not to seal rockers

    I sure would like a pic, I am just ready to do this on my cab, Planned on CRC rust inhibitor, Epoxy paint, then 3M seam sealer. Is this where the outside door gasket goes?
  12. Craig Nedrow

    Windshield washer motor questions

    My washer pump has never worked. I took the reservoir off the other day and used alligator clips to the battery and the pump works windshield wipers work, but pump won’t turn on from the switch. I really don’t want to take my steering wheel off to get into the switch, but I’m assuming it’s the...
  13. Craig Nedrow

    SBC Build Questions

    Check out Skip white, good stuff good price https://skipwhiteperformance.com/
  14. Craig Nedrow

    BBC 489 build

    Check the thing I like about Bullet cams you tell him what you’ve got in your engine and they’ve build a cam for that engine. It’s really one of the most efficient ways to do it.
  15. Craig Nedrow

    Chuck’s engine build thread!

    I used a bullet cam, Johnson roller lifters, https://www.gmsquarebody.com/threads/bbc-489-build.45389/page-4 Very good stuff. In hindsight sight, would have gone solid. The whole thread has a ton of info, lots of pics of everything, and block mods.
  16. Craig Nedrow

    6.2 Diesel Block Heater Time

    I also bought a great book put out by diesel power, I will go up to the shop later and take a picture for you. You are going to have lots of fun with that truck, love mine.
  17. Craig Nedrow

    6.2 Diesel Block Heater Time

    I had lots of trouble with my 6.2 when I first got it, here is lots of info what I did to make it a daily if you want to go through it. https://www.gmsquarebody.com/threads/new-for-me-1985-silverado-20-6-2-diesel.32359/page-6
  18. Craig Nedrow

    1964 Chevy ll ls1/t56 swap

    Just for the pic, had to go outside, it's snowing, and strip, significate shrinkage! Jan just laughed, she's does have a sense of humor.
  19. Craig Nedrow

    Chuck’s engine build thread!

    I haven't read this whole thread, but assume you will use a good assembly lube. I also take my inner spring out and run it 15 minutes at 1500 RPM. At the shop we have a dyno program, but that works fine at home. They also make lighter springs.
  20. Craig Nedrow

    Rust Repair on Squarebody Chevy

    Yep what so many others said. I bought inner outer, cab supports, and floor only to find a nice rust free cab just down the road. If you are young, that is a good thing to do as after that you are not intimidated by body work, on just about anything. Here's what I looked earlier today after...
  21. Craig Nedrow

    G series camper van forums

    It is really stuck on their good. We moved the bed in and had plywood up against it jerking it around. It didn’t even make a mark works great.
  22. Craig Nedrow

    1964 Chevy ll ls1/t56 swap

    Back half a car is now got all the old under coating off. It’s all on me now. Next is wash until clean, then alcohol everything then seam seal, epoxy primer and raptor line.
  23. Craig Nedrow

    1964 Chevy ll ls1/t56 swap

    Starting to look like a car
  24. Craig Nedrow

    Introduction and rear question

    You got the sickness same as me Zach> pretty soon you will be making midnight forays scrabbling around for a better set of may pops
  25. Craig Nedrow

    1964 Chevy ll ls1/t56 swap

    AMD Core support, very nice and the packaging was fantastic. This is just clamped on, but it makes it seem more like a completed car.

Latest posts

Forum statistics

Threads
48,666
Posts
1,074,192
Members
43,338
Latest member
hauto85
Top