Search results

  1. Old Guy Bill

    Np208 transfer case brace

    Those rods mount to plates behind the motor mounts and then to a heavy cast inspection cover on a 400TH transmission with the proper mounting holes. This pic shows the trans & cover but not the rods.
  2. Old Guy Bill

    Pulling Sucks--2001 Suburban 3/4 ton--6.0

    When you’re loaded for a trip hit one of the CAT scales at a truck stop, it’s easy and will give you a true weight of your rig.
  3. Old Guy Bill

    Truck Size

    I absolutely love new trucks. I’m a small guy, I get behind the wheel of my F-350 dually that’s 23’ long, almost 8’ wide, has 475hp, 10 speeds with over a 1000 ft lbs of torque and suddenly I’m Jack Reacher. :)
  4. Old Guy Bill

    350 to 454 in a K10: What Motor Mounts?

    My ‘78 K20 has them, and appear to be factory installed.
  5. Old Guy Bill

    Painting rally wheel rim

    The wheel has been sand blasted so just a wipe off with some cleaner will be fine before painting.. If you’ve got a can of the correct color to match your other wheels that’s plenty to paint the spare wheel. I would use some spray primer first.
  6. Old Guy Bill

    350 to 454 in a K10: What Motor Mounts?

    I don’t know the particular years but some 4x4 trucks got 1/4” plates between the clam shells and the engine, they supplied a mounting point for transmission braces. These plates can affect the mount and engine alignment.
  7. Old Guy Bill

    Fusible link burned.

    Ohms Law came into play… The lights were left on so when the battery voltage dropped the amperage suppling the headlight circuit started to climb… Now what exactly this affected is in question, maybe some wiring got hot and burned together somewhere?
  8. Old Guy Bill

    Oil sending unit hole issue

    There are sockets made for them if you can’t get vise grips on it.
  9. Old Guy Bill

    34 inch tirers speedometer reading

    From what I understand the external calibration box is required to achieve the proper ratio between the transfer case and speedometer, GM used it for a reason. They are available, but pricey $$. https://www.transfercasesolutions.com/online-store/Speedometer-Calibration-Box-p613167600
  10. Old Guy Bill

    what these studs for? A friend gave me this axel for my 73 K10 said it came out of a 73 blazer. Mine doesn't have these studs on it. I can't seem find

    Here ya go… use something like this properly and it won’t be there any more.
  11. Old Guy Bill

    Hooker small block manifolds

    They work fine with a full size starter.
  12. Old Guy Bill

    Older badge on 86 K10? Or metal 80’s era badges?

    There’s a lot of re-pop badges out there, also designs you can customize, I don’t have any idea about the quality of them though. I want something there on the fender just not sure what yet. Here’s a example: https://hhclassic.com/c-755732-truck-emblems-fender-emblems.html
  13. Old Guy Bill

    Truck Size

    One place the tall bed sides really comes into play is with a fifth wheel camper. Getting enough clearance between the bed and camper over hang is crucial. When I went to a dually it actually sat about two inches lower than the single rear wheel truck I had previously.
  14. Old Guy Bill

    Hooker small block manifolds

    I got a set of the Hooker manifolds in black. They do fit well, I used the factory bolts. They have thick flanges with a flat gasket on the output, getting ready to fit dual exhaust to them.
  15. Old Guy Bill

    Introduction from Indiana

    Hello and welcome from across the river in KY
  16. Old Guy Bill

    new here, just relotated to GA

    Welcome! but how do we really know without PICS!! :)
  17. Old Guy Bill

    rebuilt sbc Oil pressure

    Try a different brand filter…
  18. Old Guy Bill

    Introduction from Indiana

    Welcome We need pics!!
  19. Old Guy Bill

    Gears

    As previously posted we need more info.. Is it “Too high” when traveling in high gear, or “Too high” when trying to take off in low gear? Please elaborate
  20. Old Guy Bill

    Engine cranks, but only starts after letting off key? - I'm perplexed

    Just a thought… I don’t have any idea if this applies to your situation. On the older vehicles (not sure about the years?) a wire ran from the starter solenoid to the coil, this was for providing sufficient power to the coil while the starter was cranking… Are you sure about the battery itself?
  21. Old Guy Bill

    4L80 on FB Market Place

    I missed this one, but it wasn’t something I needed right now anyway.
  22. Old Guy Bill

    1978 Scottsdale Drag Link Question

    I’ve got an ORD 4” lift on my ‘78 K20, the drag link angle seems excessive to me, but this is without the cab & box on the chassis. Hopefully the springs will settle somewhat…
  23. Old Guy Bill

    4L80 on FB Market Place

    Thanks Nick That’s exactly what I thought, but wasn’t sure. I see these going for much more all the time. I’ll try to get with the guy early tomorrow.
  24. Old Guy Bill

    4L80 on FB Market Place

    I’m always looking for possible parts in my area. Saw this today, I have no experience with the later model stuff. I’m not asking about the price, I always negotiate. It’s the trans itself, year, etc.. What do you think?
View older results

Latest posts

Forum statistics

Threads
48,666
Posts
1,074,187
Members
43,338
Latest member
jw23655
Top