Search results
-
04 Buick Rainier
I'm selling my Buick since I found a Silverado that I want to buy. I have fixed it to drive and have put almost 2000 miles on it since I've had it. 2004 Buick Rainier CXL 2WD $2,900 306,000 Miles This vehicle is not perfect. Clear NC title in my name LM4 all aluminum 5.3 V8 , 2wd 4l60e... -
Power Windows Troubleshooting Info
I got around to fix the wire problem, no way to just pull the wire threw. The wire harness was wraped with tape. I had to push the entire wire harness back threw into the cab. I found three wires broke, window and both power lock wires. I had to just use butt connectors and push the wire harness...- custodian
- Post #52
- Forum: Electrical & Audio
-
LS swap firewall intermediate block/harness
I used the stock harness and fuse box. Just cut the unneeded connectors off and tucked the wires back into the harness.- custodian
- Post #4
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
02 Cluster in a 73 C10
Well, I gave upon trying to put the Silverado cluster in the 73 bezel. Just couldn't get it pictured right in my head on how it should look.- custodian
- Post #21
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
Jack strap no... not jock strap
You can have them, just send me your address. I'll be at a swap meet this weekend so it will be next week before I can ship them. -
Jack strap no... not jock strap
That's all I have. The truck didn't have a jack when I bought it. -
Jack strap no... not jock strap
Also I have this that's still on the original inner fender. I changed inner fenders about six years ago, but still have them. -
-
Jack strap no... not jock strap
If AyWoSch doesn't have what you want, I took mine off the 73 when I did my LS Swap. Should still have it. -
To Cut Or Not To Cut
I've decide to remove only the wires that I need from the connector, turn signals, fuel gauge, temp and high beam.- custodian
- Post #39
- Forum: Gauge, Speedo & Instrumentation
-
To Cut Or Not To Cut
To all those out there that might be looking for the cluster pin out, here's what I was looking for.- custodian
- Post #34
- Forum: Gauge, Speedo & Instrumentation
-
To Cut Or Not To Cut
Anyone have the pinout wire diagram for the plug that goes into the back of the gauge cluster for a 73 C10?- custodian
- Post #32
- Forum: Gauge, Speedo & Instrumentation
-
AN Fittings
No wiggle on the bottom connector, just some in and out movement on the other connector. The rubber braided hose connection is tight, no movement.- custodian
- Post #5
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
AN Fittings
This is the type of fitting I have. The part that is lose is the tube coming out of the fitting under the word "AUTO". The pipe will move slightly in and out.- custodian
- Post #3
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
AN Fittings
I've never used AN fittings before. I bought a kit to use for my trans lines on the LS Swap. After getting everything put together, I found the the fitting part just above where the hose connects is loose. It's not lose where the two pieces mate together, it's loose at the pipe piece just above...- custodian
- Thread
- Replies: 5
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
Autometer Gauges
Thanks, I'll write them down.- custodian
- Post #3
- Forum: Gauge, Speedo & Instrumentation
-
Shifter Needle
That's what I was looking for. Easier to just buy the entire piece. -
Shifter Needle
I need the shifter needle for an 85 C10 with a 700r4 overdrive transmission. I broke the shifter needle while working on the 85. -
-
-
-
-
Heater control
I have this, but one of the mounting tabs is broke off.
