Search results

  1. Ken B

    Fast Idle

    SOrry 350cu T350 trans. all swapped in in the last year and never ran since really
  2. Ken B

    Fast Idle

    I have a fast idle start up with NO cruise control. I will look at throttle cable and see that its free, any other suggestions? No muffler right now so being a nice neighbor and letting people wake up naturally, not to a 350 with no muffler......
  3. Ken B

    fuel venting

    Question #2 The very small pvc line with green tape, hard to see, does that go to the port on the carb with the green tape? Lots of tubes with screws plugging them that I didnt do so I am just trying to confirm and re plumb these lines
  4. Ken B

    Looking for a heavy-duty receiver hitch

    that is a beefy bumper. looks good , nice work!
  5. Ken B

    fuel venting

    So the line with the white tape goes to the air cleaner, I understand and found where that connects. what I do not know is why is there a T in that line and were did or should it go? If not needed can I delete the T ?
  6. Ken B

    DapeanutKid Here and New To GMSB 1974 C10

    Welcome from INDY
  7. Ken B

    fuel venting

    Looking to get this plumbed up. This is a swap 250 to 350 so my core has the old routing. Where do these land? Or where can I find the routing. Please and Thanks
  8. Ken B

    Stepside bed hits gas tank

    Gotcha. Scary that the bed and tank were rubbing
  9. Ken B

    fuel venting

    I wish I could. Old pic. Already got cab on. And would prefer not to drop tank
  10. Ken B

    Stepside bed hits gas tank

    did you take the wood bed sills out and maybe have them in the wrong order. i thought there were 2 different sizes....maybe I am mistaken ....or i dreamt it
  11. Ken B

    fuel venting

    so what I am looking at doing is cutting in a T on the fill hose vent line to attach my return vent from the charcoal cannister....is this a good or bad idea ? obviously would need something compatible with gasoline . Looks like maybe a 3/4 vent hose for fuel filler....
  12. Ken B

    fuel venting

    I have fuel in and out of fuel pump and to carb done, i think. I have a hard line that runs across the front to charcoal canister and to the rear of the truck where do I land that hard vent line from the canister?
  13. Ken B

    fuel venting

    I am worried that thereisnt a vent.
  14. Ken B

    fuel venting

    OK so I need help( such a loaded statement). I am trying to get my fuel system vented. 1981 c10. I have a 2 port sending unit in the gas tank. 1 out , 1 return. I have a mechanical fuel pump, 1 inlet 1 return and one line running up to the carb. My problem is memory is terrrible. The vent ...
  15. Ken B

    Bringing the Cat back...enough is enough.

    Good Read.... I am gonna do a cat. just wondering if its duals? My son is trying to talk me into ceramic headers, stainless exhaust , duals, no cats. This is a truck not a racer, he had a 9.6 second 392 charger w NOS.....the old man wants a good quiet exhaust the lets the motor breathe as...
  16. Ken B

    Air inlet on the core support?

    10-4 appreciate your knowledge
  17. Ken B

    Air inlet on the core support?

    i knocked it out on the pass side. was just wondering about the opening getting covered on drivers side. I may try and tack the knockout back in on the unused side.
  18. Ken B

    Air inlet on the core support?

    Resurrecting an old thread. I am moving the air ducting from drivers to pass side. Is there a problem leaving the plastic air inlet piece on the core support open or not connected to anything? Any problem with directing air to the air inlet tubing with the opening on the otherside allowing air...
  19. Ken B

    horn(s)

    is there a recommended soak time.?
  20. Ken B

    horn(s)

    bucket you got a "juice" of preference wd 40, pb blaster or are they all the same
  21. Ken B

    horn(s)

    My assumption is 80s horns.
  22. Ken B

    horn(s)

    my 81c10 has 2 horns but only one is working....looking for a stock replacement anyone looking to get rid of one.
  23. Ken B

    Brakes

  24. Ken B

    Brakes

    the pv tool that centers the pv while bleeding helps. I went thru 1 new chinese prop valve then spent a little more on a 2nd one and it didnt leak
  25. Ken B

    temp sensor

    thanks for the info. this not my original engine its a late 80s-90 engine. bushed to fit i did see that. guessing the bushing may try and come out when i try to remove sensor we will see. i think the sensor is a 13/16 socket to remove from the research I looked at. shoulda done this when the...

Latest posts

Forum statistics

Threads
48,666
Posts
1,074,187
Members
43,338
Latest member
jw23655
Top