Search results

  1. Camar068

    What have you done to your square lately??

    wonder if a good cleaning, then taking a heat gun to the lens if they would "rejuvenate" the plastic? I think I have a few old spares I can try it on.
  2. Camar068

    1984 K10 LS Swap - Lots of Little Problems

    Also just thought about this, on one of my injectors either the T|T on it is broken off OR the connector part that goes over it is broken (can't remember which lol). I've got it zip tied but a hard enough bump will cause it to jump off and run really bad.
  3. Camar068

    1984 K10 LS Swap - Lots of Little Problems

    not reading the whole post and/or remembering, did you ohm the #2 injector and coil wires back the to ECU and then the grounds for each? Sorry if you have, nothing meant.
  4. Camar068

    What new tools have you got lately?

    comes with hooks to hang tools on the side also, but not installed. You can use the cheaper ones that come in a 2 pack, but I'd given the 2nd one to a neighbor because I didn't need it at that time. Live and learn lol.
  5. Camar068

    New here

    Very Nice....Welcome from east KY. Feel free to use the search button.
  6. Camar068

    What have you done to your square lately??

    Drilled holes in floor to help with rusted cab bolts. Figure I'll flood daily with wd40 for a week before i try. 11.5" off the wall and 2 .5 off the bend. Thx to the dude that put up the youtube video (screenshot of it).
  7. Camar068

    What have you done to your square lately??

    hit a rough drop off in a construction area. The hump over the rear exhaust broke loose. Time for some exhaust....or whack off the passenger side and save $160 until I'm ready to go from 2 1/4" to 2 1/2".
  8. Camar068

    What new tools have you got lately?

    Got these yesterday Order this also cuz I need room for more
  9. Camar068

    4l60E flush

    I'm not getting it.....are you saying I can pull the pan and ALL the fluid is changed? My understanding is about 6 qts of fluid is changed. Thx Dingo
  10. Camar068

    What new tools have you got lately?

    Keep the tank dry so you can pass it on to your family.
  11. Camar068

    1984 K10 LS Swap - Lots of Little Problems

    Might try an old school timing light on each spark plug wire and wiggle wires. Just a thought.
  12. Camar068

    Headlight buzzer

    I'm good lol, I've got 4 spares now.
  13. Camar068

    Headlight buzzer

    5 pc buzzer
  14. Camar068

    Headlight buzzer

    and u didn't bring me one? lol just razzin' anyway, yeh it crapped out....now replaced and working good. Funkinesium (loud) from amaswan so I had to put a lot of electrical tape on it to chill it out....A LOT lol. $6 for 5 of them.
  15. Camar068

    4l60E flush

    My trans lines are cut and have rubber hoses on them. Would it be fine to feed IN new fluid outta one container and OUT old into another out of the other line? Do this before or after filter change? Also, thoughts on seafoam trans before hand? I've been a believer of seafoam since a few...
  16. Camar068

    1984 K10 LS Swap - Lots of Little Problems

    Not sure what would happen if you installed larger injectors and it not tuned for them. Just a thought.
  17. Camar068

    Steering box

    from reviews yes.
  18. Camar068

    4L60E Information Thread (Includes 4L65/70/75)

    Thx Nick. Any suggested pan under $100 (deep pan)? Was gonna go with Jegs 61183 but one person left a review about the servo exhaust/bleed hole vent and having to grind down the pan in that area. If anything I'll slap the original back on.
  19. Camar068

    4L60E Information Thread (Includes 4L65/70/75)

    fluid/filter change coming soon. Demand Dex/Merc for 2006 4l60e (4x4) stock LS swap or let him talk me into newer? Might be doing myself pending his price....but I trust his evaluation of trans (over 100k).
  20. Camar068

    Need help finding short for electrical ground

    Thought I'd add it here to share: The Big 3 Sticky
  21. Camar068

    Big 3 Upgrade

    Big 3 write up here on GMSB. Thought I'd share while looking for it to put in another post. The Big 3 Sticky
  22. Camar068

    What have you done to your square lately??

    Great....now I want a press.
  23. Camar068

    4L60E deep stock aluminum pan w/drain upgrade?

    Are there models of the 4l60E pans that were stock, aluminum and with a drain plug? Looking at options. Looks like I can get a normal pan for $30-50 with a drain plug. If I can go to a junkyard and get one that's thicker w/drain plug, I'll go that route if it's reasonable.
  24. Camar068

    What have you done to your square lately??

    received front/rear brake pads, front hoses, rear wheel cylinders and will warranty exchange front calipers. RF locks up when extremely cold or has rained. Autozone is nice enough to exchange both front calipers even though only one is locking up. The plan is to change the fluid first with...
  25. Camar068

    LS swap oil pan

    grrr.....just saw this. Again read up on it. From ORD at the bottom of the link above: "For LS swaps using the Dirty Dingo “Slider” motor mounts there may be possible oil pan clearance issues with the stock truck style oil pan. A high clearance pan may be necessary." My apologies.

Latest posts

Forum statistics

Threads
48,666
Posts
1,074,180
Members
43,338
Latest member
jw23655
Top