Search results

  1. Camar068

    What have you done to your square lately??

    THought i had a rod knock a few weeks ago....but it didnt sound right. Monitored codes on the LS for about a week as it got worse. Drivability it didnt change....juat the sound. And neighbor was following the sound away from the engine to the back as it warmed up. In the end the cheap ass...
  2. Camar068

    Flattening the Floor to Allow Use of Any Seat

    Pretty sure there's a post/sticky on removing the saddle tanks and then getting rid of the humps to allow ease of installing whatever seats you want. Been a while, but I'm pretty sure it's here on GMSB.
  3. Camar068

    Motor mounts

    lol and toss those old bolts in a bucket or bin.
  4. Camar068

    Need Alternator help please

    just a thought, check wiring under your fuse boxes and such. Also check your ground cables and make sure their good.
  5. Camar068

    77 K10 LS Swap

    if you have to notch it....it's not enough to worry about. I didn't notch mine because when it was installed the vent hose for the front diff got pinched there and I thought....good enough lol. I ran another hose for the diff. Honestly it's not much to clear.
  6. Camar068

    LS bellhousing stiffener rods

    before I did my swap, they were there but not hooked up. With that I deleted since they didn't fit anyway. I used the 5.3/4l60e/adapter out of a 2006. No issues, but I'm not lifted more than stock.
  7. Camar068

    What have you done to your square lately??

    want a 4x4 so bad lol.
  8. Camar068

    G series camper van forums

    Vemco V-drive. IFS built for chevy.
  9. Camar068

    Best "Sweet Spot" on a radiator?

    might be able to get the controller from an early 2000's chevy and put it to work with a few mods. 3 relay system so if one fails it switches to the other fan. Actually I think if 2 relays fails it will switch to one fan.....don't hold me to it....been a while since I looked at the schematic.
  10. Camar068

    Best "Sweet Spot" on a radiator?

    same, it's peace of mind having a controller and 2 fans. One fails, it switches on the other.
  11. Camar068

    What have you done to your square lately??

    hmmm.....cut some good styrofoam so they mount flush on the surface (be a good cushion for the tweeter). Then use fiberglass resin around that (maybe with the glass or shop towels) to act as the tweeter case. Block of wood on the bottom to use studs or screw into. Resin over the bottom as...
  12. Camar068

    What have you done to your square lately??

    plenty of videos and reviews on yewtube
  13. Camar068

    What have you done to your square lately??

    I had JBL 6 1/4 component system behind the seat. Well the plastic mounts breaking and such, it started to rattle. I went out on a whim and got some Pioneer 6x9 5-way. They suck arse compared to the jbls's I had. I may be looking to find a way to get them back in there. Hardest part is the...
  14. Camar068

    XJ steering shaft mod

    should be moved to the proper post for future reference and success/fails on the mod.
  15. Camar068

    3.08 Gears. What to Swap to?

    I went from 3.08 to 3.73 on a stock k10 with 4L60e. I wish I had 3.90 or 4.10 now. The lower gears would put it in the rpm range I'd like from 70-80 mph on the interstate. In OD, it's right on the edge of "ok...lets go" at 80. At 85 it's begging for more gas lol. We have hills and mountains...
  16. Camar068

    "Oldsmobile Diesel" Conversion to gas

    Read up on this before you ditch it....not just this article....others as well. https://www.hotrod.com/how-to/wise-performance-engineering-465ci-oldsmobile-engine
  17. Camar068

    What new tools have you got lately?

    ah....missed the fire skid part lol.
  18. Camar068

    What new tools have you got lately?

    Northern tool has a spray head for $30 that has a 17' spread at about 4.5' off the ground. I use it to spray my yard. Spray nozzle Can't vouch for the next one, but it's metal and 1/2" instead of quarter. Also handles larger flow pumps....and is $20. Metal Spray Nozzle
  19. Camar068

    What new tools have you got lately?

    nice, thanks for the info. I'll be getting a pair soon.
  20. Camar068

    Adding second fuel tank and efi fuel pumps

    Tank relocation: https://www.gmsquarebody.com/threads/write-up-gas-tank-relocation.663/
  21. Camar068

    in tank fuel pump

    I've got the burb tank under my bed so it's easier for me to pull the bed. But with you having saddle tanks, it's a toss up. Although it appears you have a long bed dually....may be more difficult to pull the bed. Of course, when you have the bed off, you'll be able to clean up any rust and...
  22. Camar068

    305 serious sludge

    don't be afraid to do the seafoam or other name brands to break down the sludge in the engine. Some manufactures say drive it for a few hundred miles after adding and others say do it in the driveway for a certain amount of time. I've done both versions and they work if you stick with name...
  23. Camar068

    What new tools have you got lately?

    we've got a vendors mall up the road. Similar to your pics is whats in there. It's been years since I've been in there. May need to hit it up again.
  24. Camar068

    picture needed bucket seat bracket

    lol italics not allowed?
  25. Camar068

    What have you done to your square lately??

    Swapped out the fuel pump on the LS swapped rear burb tank.

Latest posts

Forum statistics

Threads
48,666
Posts
1,074,187
Members
43,340
Latest member
hauto85
Top