Search results

  1. D

    Suggestions for replacing this?

    Float its captured, meaning just let them rest together without welding them together?
  2. D

    Suggestions for replacing this?

    I've read that these aren't made anymore. This is the sleeve for the body mount bushing on the passenger floor. All the others were in decent enough shape that I cleaned them up, painted and reused. Anybody know where to get a replacement?
  3. D

    Interior Journal

    I got the grill removed and the two core support body mount bushing removed today. Neither one was tight - they both spun freely with fingers. So far that makes 3 out of the 5 I've removed so far not even close to tight. Time to try number 6 - passenger side floorboard
  4. D

    Interior Journal

    Looks like you have it worse than me for sure
  5. D

    Interior Journal

    Well i spoke too soon. Shockingly, the passenger side is completely loose - I'm talking i can spin it with my fingers, and also push up and down on it. It has been doing absolutely zero to keep the cab in place. Anyhow, the captured nut is just spinning on pass side. I made another hole and will...
  6. D

    Interior Journal

    I got the two rear cab mount locations figured out today. I preemptively used a hole saw on the driver side cab floor and peeled it up to expose the captured nut. I assumed I'd need to before i even started but turns out the bolt came out without needing to access the nut. Everything I've read...
  7. D

    Interior Journal

    I think I finally have most of the rot out. I was NOT expecting this much when I started lmao. Got the first cab mount bushing out and a bunch of new panels from LMC here Next part will be to clean up as much of the surface rust I can still see and spray it down with some rust converter and...
  8. D

    Interior Journal

  9. D

    Interior Journal

  10. D

    What is this part called, and are they available anywhere?

    Thank you
  11. D

    What is this part called, and are they available anywhere?

    Kind of hard to see in my picture, but it's a piece of sheet metal that sits on top of the tee intersection of the two cab floor supports, and covers up the captured nut for the body mount bushings. I had to completely destroy mine in order to get it off, so that I could remove the cab floor...
  12. D

    Interior Journal

    Good info, thank you. Luckily, so far anyway, all the welding I have to do except one small spot on the outside of the rocker will be hidden under carpet
  13. D

    Interior Journal

    Cab floor support is trash
  14. D

    Interior Journal

  15. D

    Interior Journal

    It doesn't look like the new pans will reach up that curve of the seat hump so I'll have to figure out what to do there Also, those little spot welds across the bottom of the door threshold are weird looking. It doesn't look factory to me but I've never gone this far into one of these things so...
  16. D

    Interior Journal

  17. D

    Interior Journal

    Cut out some of the rot today on the driver side. I have floor pans here, the rockers are on order from LMC. The rocker isn't as bad as I thought it'd be, just a small spot on the outside I cut out. The interior of the rocker doesn't ok great but I'll get a better look once the floor pan is...
  18. D

    77 K10 - what should I be asking for?

    Purchased for $3200 about 5 years ago Everything listed below has been performed by myself within last few years, with less than 500 miles driven since I've owned Complete rear-end rebuild, new bearings, ring and pinion and TruTrac with aftermarket different cover All brand new u joints All...
  19. D

    Interior Journal

    For some reason the driver side floor pan picture didn't upload, but it's the worst of it. There are several small chunks of metal completely missing and can see through.
  20. D

    Interior Journal

  21. D

    Interior Journal

  22. D

    Interior Journal

  23. D

    Interior Journal

    Starting on interior. Today I pulled the bench seat the floor matting and padding. Found a few ventilation holes in the floor pan. Looks like I am going to be learning how to weld
  24. D

    No power at all, zero lights, guage lights, or anything else. Any help wld be great.

    Did you install a shim on your starter? If so you may want to remove it and try again, sounds like the starter is too far away from the flywheel
  25. D

    Dakota Digital RTX Install Critique

    For future readers - water temp and tach both get fed thru the PF4 BMI and outputs directly into the DD gauges so no need to run the extra wiring. Only need to install the oil pressure sender and wiring Still trying to figure out how to get the GPS BMI to output correctly tho

Latest posts

Forum statistics

Threads
48,666
Posts
1,074,162
Members
43,334
Latest member
Nborden88
Top