Search results

  1. V

    need 208C case front 1/2

    I thought I had one, but am only finding the rear 1/2 of the case.
  2. V

    Cruise Control Linkage Needed for an 87 tbi

    This should be it. About 8” long. Adjusts by hand, so not frozen up. @Hunter_Michael
  3. V

    Cruise Control Linkage Needed for an 87 tbi

    I’ll try to remember to look tomorrow. Believe I still have the cruise stuff from an 89 Blazer I parted
  4. V

    Wife’s new toy

    Picked up some used wheels (17x9) and tires as 3 of the steel wheels that was on it has pin holes rusted in them. She is not sure yet if she likes the looks of these, but got them at a good price. Will polish them back up eventually. Slowly getting more and more of the red and yellow off the...
  5. V

    Hello from Tn

    Welcome from SW MS. I get to mid Tenn a good bit and have looked for land east of there around the Monteagle to Jasper area.And as far north as around Soddy Daisy.
  6. V

    Needing help locating an air filter duct

    I’ll look as I still may have the one off the 88 CC that I still own, as it was a 454 truck
  7. V

    What did I do wrong? NV4500 Swap Issues

    Looks like there is no pilot bushing installed in this photo. Be sure to install one if you haven’t already
  8. V

    84 OEM Cruise Control Module/LS Swap

    Here is how I am looking into doing my next set up. It’s s10 but the full size stuff is almost, if not same. https://s10lsswap.wixsite.com/my-site/post/guide-how-to-make-s10-cruise-control-a-standalone-unit-for-use-with-any-dbc-setup
  9. V

    2000 6.5 turbo on a 82 6.2 diesel?

    Do you have factory a/c on your 82? The 6.5 turbo setup will hit the ac box. If your truck just has the heater, it will be fine. The down pipe will have to be fabricated. Looks to be a non egr intake too which is good. You can plug the map sensor and such as it is not needed with mechanical...
  10. V

    Camber issue

    In the 80s, we’d cut a square out around the lower ball joint, cut 5/8” out behind the ball joint, then weld the ball joint piece of the control arm back in. Saw one of the trucks about 3 years ago, that I did in the 80s, still running around with the 4” drop springs and modified lower control...
  11. V

    87 v3500 6.2 engine replacement

    What is your plans / use for the truck? We still find running 6.2 pullouts reasonably priced here in SW MS. Without a turbo, they are no powerhouses, but you may can find one cheap enough to get truck going for now. And can round up parts for later. Edit: I get my 6.2 pumps rebuilt at the a...
  12. V

    K10 Evaporator Box

    I’ve probably got 1 or 2 spare boxes in the barn. Will try to remember to look when I get home from work
  13. V

    Wife’s new toy

    Wife mentioned a while back that she would like an old Bronco or Scout, since her father had both when she was growing up. Visited a buddy (we’ve known each other since we were about 10 yo or so) a week or so ago to seeing how he was getting along with his pending divorce. He had this out...
  14. V

    Castor shims

    On the IH Scouts, most of the housing c’s are welded with zero caster built in. A “cut and turn” is common on those vehicles.
  15. V

    Looking for bench seat options with a foldable back / armrest

    I used 2014 Ram seats with the folding console that has cup holders.
  16. V

    Need a pic of a tank selector valve shield for a 1987 V10.

    Factory shield off an 87, with upper support rod.
  17. V

    1989 Blazer main dash, and tbi harness (may fit other years)

    $100 each shipped in lower 48
  18. V

    What new tools have you got lately?

    Bought a few jars, for the harnesses that DON’T pass the smoke test.
  19. V

    1989 Blazer main dash, and tbi harness (may fit other years)

    $125 each shipped in lower 48 or $180 shipped for the pair, shipped in lower 48.
  20. V

    Need a pic of a tank selector valve shield for a 1987 V10.

    Let me look, I may have one or two spares.
  21. V

    K5 ls swap

    ….
  22. V

    What size/length/thread pitch bolts for brace on NP208 transfer case?

    Let me look, I think I have a few extras. If so, I’ll send you one.
  23. V

    6.2 Liter diesel return line

    I’ve got a few parts 6.2s, if i’ll try to remember to look when I go to my other property, as none of the ones I have here have it. Should be 3 or 4 motors still in that barn. Plan to go get a trans and case from there soon.
  24. V

    Let’s see your memorabilia?!

    Was sent these the other day from a 90 plus year old man that retired from the state of Louisiana. Will talk to him to make sure I have the story correct but: When the Baton Rouge arsenal swapped from flintlocks, to percussion muskets they had hundred of French flints for the old flintlocks...
  25. V

    6.2 Liter diesel return line

    I’ve got a few parts 6.2s, if 82diesel doesn’t have one.

Latest posts

Forum statistics

Threads
48,416
Posts
1,066,933
Members
42,801
Latest member
rafamartz
Top