Search results

  1. C

    Chevy k10 rally wheel beauty rings

    Where can I find flat edge style beauty ring ? Overall 3 inch in width and I like the low profile and flat outer edge. All other ones I see are rounded edge and don't fit the valve stem well. I just ordered some from classic parts of America thinking it would be these as it stated 3" but they...
  2. C

    1987 V10 with crossover steering - knuckle question

    Anybody using this steering knuckle for crossover steering? Looks like it is slightly rubbing my axle tube at the top and my tire on that side is leaning inward at the top. So I think negative camber. All new Delco ball joints and ORD crossover steering system, I thought the turning radius...
  3. C

    Issue after crossover steering installation

    I have both the bolt on and weld on brace on. Would a C30 pump work better? I heard they have higher pressure output
  4. C

    Issue after crossover steering installation

    Mine is a reman 2wd box from Napa, do the 2wd boxes need more pressure?
  5. C

    Issue after crossover steering installation

    Wheels jacked up off the ground, lock to lock more times than I can count
  6. C

    Issue after crossover steering installation

    Didn't do that before the crossover install, wonder if I blew the pump going from stop to stop when bleeding, or it is just a **** pump like most these days
  7. C

    Issue after crossover steering installation

    Belt is tight and spinning the pump fine, no squeal
  8. C

    Issue after crossover steering installation

    Just installed ORD crossover steering on 1987 Chevy v10, got a 2wd reman box from Napa for this since it requires 2wd box. The Power steering pump is a reman but worked fine before the conversion, now with everything buttoned up and the system bled time and time again, I have no power steering...
  9. C

    1987 Chevy v10 wipers won't park in down position

    New wiper motor, worked great a couple of months ago when I first installed it. Also new washer pump, worked great when first installed a couple of months ago. Now the pump doesn't work and the wipers are parking in the middle of windshield each time. I am getting power to the washer pump but...
  10. C

    1987 Chevy V10 steering wander

    I'll call them this week, gonna be tough to watch them with work schedule. As for using a fishing scale on ball joint preload, how exactly would I do that? Just hook the scale right onto the knuckle then pull?
  11. C

    1987 Chevy V10 steering wander

    Didn't get one, I think all they did was set the toe
  12. C

    1987 Chevy V10 steering wander

    Can I do this with hub and rotor attached ? How do I adjust it if it is too tight?
  13. C

    1987 Chevy V10 steering wander

    Had the alignment done and it still feels the same, maybe a bit better, when I did the ball joints the knuckle preload did feel tight. Maybe this is the issue ? Should I loosen the preload sleeves on the upper ball joints?
  14. C

    1987 Chevy V10 steering wander

    Going to take it to an alignment shop this evening, seems like the caster is off hopefully they can get it right
  15. C

    1987 Chevy V10 steering wander

    Sticking side to side, how do I set the preload on the knuckle? They seemed tight when I did the ball joints, I torqued the upper ball joint adjustment sleeve to spec
  16. C

    1987 Chevy V10 steering wander

    The one I put on there is a skyjacker, can't tell if that's the issue but I doubt it
  17. C

    1987 Chevy V10 steering wander

    What What else can they adjust on a straight axle ?
  18. C

    1987 Chevy V10 steering wander

    1987 Chevy v10 on 2 inch lift rear blocks, all front end components new. Steering box is new with weld on brace and bolt on brace, XJ shaft, new stabilizer, heavy duty tie rod from Off-road design. New ball joints and TREs everywhere. Around 35-50 mph I feel like I may lose end up in the other...
  19. C

    Toe adjustment 1987 V10

    I'll just trim some off the tie rod ends
  20. C

    Toe adjustment 1987 V10

    Not now lol, confused as to what is original for this truck now
  21. C

    Toe adjustment 1987 V10

    I think the driver side with the hole in the TRE is way too long, I still have about 2 inch of thread left on it, the adjusting tube doesn't thread that deep. On my 87 v10 originally come with the 7/8 long adjustment tube or was something swapped?
  22. C

    Toe adjustment 1987 V10

    Eyeballing it until I can dial it in, it looks way off as it sits, both tires pointing outward a good bit
  23. C

    Toe adjustment 1987 V10

    I have an 87 v10 and my toe is out, the front end of my front tires are poking away from each other. I have the long adjustable tie rod with the tie rod ends on each end. I have adjusted the tie rod as far as it will go and the tires still aren't close to parallel. It's almost like my tie rod...
  24. C

    Chevy k10 steering arm cones

    Nuts reusable too?
  25. C

    Chevy k10 steering arm cones

    Hey all, in the process of putting new ball joints and axle u joints on my k10 with a 2 inch lift. Wondering if I can re use the cones and nuts for the stock steering arm? I dinged them a little with a flat head as they are a bear to get out. But overall in good shape and I have reason to...

Latest posts

Forum statistics

Threads
48,413
Posts
1,066,821
Members
42,794
Latest member
Huffer8
Top