Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Ricko1966's latest activity
R
Ricko1966
replied to the thread
Overheating 87 TBI
.
I'll find a pic of the bypass hole for you,with no bypass there is no circulation so the thermostat doesn't get hot water circulated too...
Mar 6, 2025
R
Ricko1966
reacted to
rys272's post
in the thread
Overheating 87 TBI
with
Like
.
you’re talking about how there’s that fifth hole on the front of the block where water pump bolts overtop of may be plugged? This is the...
Mar 6, 2025
R
Ricko1966
replied to the thread
Overheating 87 TBI
.
It's a circulation issue,not fan clutch,not head gaskets etc. Otherwise the 2 holes in the thermostat wouldn't have stopped the...
Mar 6, 2025
R
Ricko1966
replied to the thread
Overheating 87 TBI
.
When and how did this start? Is this the original tbi engine? Is the heater core hooked up?
Mar 6, 2025
R
Ricko1966
reacted to
bucket's post
in the thread
Early 4.3 upgrade?
with
Like
.
Just pointing it out in case it wasn't obvious... that's and old article and the 4.3 lived on for a good number of years after '98. I...
Mar 6, 2025
R
Ricko1966
replied to the thread
Dash Pad Help
.
I'd be tempted to skin it with fiberglass then fill it sand it make necessary cut outs and make a painted dash. I've done it on a couple...
Mar 6, 2025
R
Ricko1966
reacted to
Tonimus's post
in the thread
14 bolt FF missing parts?!
with
Like
.
I don't know that I would say dangerous, as the key was acting as the lock washer and lock nut. May have been a bush fix. Nothing is...
Mar 6, 2025
R
Ricko1966
replied to the thread
BBC 396 wil not idle with any carb
.
If you can't get it to idle you can't set timing anyway, so put it where ever it runs best for now. If the rpms are too high the weights...
Mar 6, 2025
R
Ricko1966
replied to the thread
Early 4.3 upgrade?
.
Lots of info on 4.3s here https://www.s10forum.com/threads/the-holy-grail-of-4-3-info.131868/ Very valuable stuff in post #2
Mar 6, 2025
R
Ricko1966
replied to the thread
BBC 396 wil not idle with any carb
.
New O.E means nothing at this point,different engine,different carbureator,different intake,camshaft,etc. put it on manifold vacuum,you...
Mar 6, 2025
R
Ricko1966
reacted to
Rustisbest's post
in the thread
BBC 396 wil not idle with any carb
with
Like
.
Your vacuum advance is still on ported if that's a picture from today. Bigger cam is gonna need extra idle timing. Air gap intakes idle...
Mar 6, 2025
R
Ricko1966
reacted to
Rustisbest's post
in the thread
BBC 396 wil not idle with any carb
with
Like
.
Good luck. I tried.
Mar 6, 2025
R
Ricko1966
replied to the thread
BBC 396 wil not idle with any carb
.
Did not know you had checked fuel pressure and had a full filter. My bad.
Mar 6, 2025
R
Ricko1966
replied to the thread
Qjet to 2bbl swap?
.
This is why on a qjet you do all your jetting and tuning on the primary first,most of your driving is on the primaries. Don't change...
Mar 6, 2025
R
Ricko1966
replied to the thread
BBC 396 wil not idle with any carb
.
Have you checked fuel delivery,if it will take throttle with choke closed,you either have not enough fuel,or too much air. See how much...
Mar 6, 2025
Latest posts
Need help identifying 12v wire for electric choke
Latest: Edelbrock
15 minutes ago
Electrical & Audio
G
rear tailgate power window motor Blazer/suburban
Latest: gmbellew
42 minutes ago
Electrical & Audio
GMC-IH
Latest: dragstews
48 minutes ago
Other Vehicles
Let’s see your memorabilia?!
Latest: 410 John
Today at 11:29 AM
Garage
A Technical Comedy [Only After the Fact]
Latest: Sad Sack
Today at 11:24 AM
Tech Discussion
Forum statistics
Threads
45,666
Posts
989,012
Members
38,761
Latest member
Paez1967
Members
Top