Recent content by murdrd87

  1. M

    1987 R1500 TBI 350 ignition module question

    Yea, I use the dielectric grease
  2. M

    1987 R1500 TBI 350 ignition module question

    Parts store brand, Borg Warner
  3. M

    1987 R1500 TBI 350 ignition module question

    Anybody
  4. M

    1987 R1500 TBI 350 ignition module question

    Need HELP? Need some help? I have a 87 r1500 tbi 350. A few months ago I was having problems with the ignition module blowing out all the time, found out my alternator was the problem, my alternator was old, so I replaced it with a new Powermaster alternator, and never had another problem with...
  5. M

    87 r1500 TBI question

    I have a holley projection intake and holley 670 tbi on my 87 350. Can I take the holley throttle body off and run a stock throttle body. I hate the holley tbi, I know the intake has 2 inch bore openings but do they make a gasket or adapter the will allow the stock tbi to work with the holley...
  6. M

    1987 R1500 Tbi 5.7

    Question guys? I have a 1987 R1500 tbi 5.7, I have a holley intake and throttle body on the motor, everything else is stock. I have replaced all the sensors on the truck. I eliminated the egr valve over 8 years ago when i bought the truck because it did not affect the emissions, I pass emissions...
  7. M

    Hypertech streetrunner chip for 87 r10 350tbi

    Has anybody ran a hypertech chip in their 87 r10 or r1500 350 tbi, are they worth the money or can you tell a difference. Hypertech makes a street runner chip for 87 r10 350 tbi. I have headers, holley intake and throttle body on the motor, everything else is stock
  8. M

    Throttle position sensor question

    Ive got a 87 r10 with a holley 670 tbi and a aftermarket intake on a 350, holley says to set the tps on .65 volts, with ignition on not running. Has anybody had the tps set higher or lower tthat made it run better. Just wondering.
  9. M

    Voltage issues on a 1987 R1500

    I own a 1987 R10 truck, I've been having issues with the ignition moudule blowing out, the voltage will spike to 18 volts and just kill the module. I've replaced the Coil, ignition module, disributor cap and rotor button, it has new plugs and plug wires. Back in January I put a new aftermarket...
  10. M

    1987 GMC r1500 vent window glass replacement.

    How do I replace just the glass on the vent window. The glass shattered and just need to replace the vent window glass. Do I have to take the vent window frame off.
  11. M

    HELP Fuel/Throttle body issues

    I have a 87 GmC R1500 with a 5.7 TBI, I am running a Holley 670 tbi, I was sitting in a line at idle, I looked down at my voltage gauge and it was showing 18 volts,when I was pulling out on the road my truck completely died, I can turn the truck over, but it does not crank, I am gettin fuel up...
  12. M

    Autometer Tach Wiring

    you ask a question for help, and fckers view and dont respond, nothing like it. Takes may 2 seconds to be like hey try this but its all good
  13. M

    Autometer Tach Wiring

    Quick question, what size wire would you use to wire in a autometer tachometer. 18 guage wire or 14 guage or something else.
  14. M

    1987 C10 5.7 TBI check engine light on.

    I have a 1987 C10 TBI 350, I have recently changed the Intake manifold from stock to a Holley Projection Intake. Put everything on and cranked it up and everything was fine, checked timing the way that your supposed to do. Everytime you crank it, it would turn right over and run fine. A couple...
  15. M

    Setting Timing on a 87 C10 350 TBI

    I was wanting to know the right way to set the timing on my 87 C10 truck. Its got a 350 TBI and I had replaced the intake on it and now i just need to set timing. I know your supposed to disconnect some wire, need to know where the wire is at. I have a timing light. Didnt know know if i had to...
See more

Latest posts

Forum statistics

Threads
42,178
Posts
910,756
Members
33,673
Latest member
jcuriel512
Top