Hi Jesse,
After selling my old engine and trans I am into this swap at around 5K. That being said, I had to pay someone to swap the engines out (I don't have the means to do it), bought a 2011 5.3 w/6L80 with 38K on it for $3500 (this part can be done cheaper), I paid for my harness to be...
oneluckypops......where were you when I needed you...lol I didn't know anyone did wireing harnesses arouned Houston or I would have looked you up! Could you tell me the name of that pull-a-part yard, I have been looking for one of thoes for a while!!
I am still pulling 2 codes for Lean System...
Alright, here is some vid of it running
https://www.youtube.com/watch?v=JxCBf5ER50k
https://www.youtube.com/watch?v=dHZo8uDOKDQ
https://www.youtube.com/watch?v=WONDIfhAOiI
Lemme know what you think and thanks for all the help!
Here are the part numbers that I bought from Summit. I don't have them yet but have found some people that used them and it works!
ATM-2259
ATM-2277
goes into the pass head where the allen bolt is located.
Well, I got my PCM back from the tuner and what do you know......it started and stayed running!! I hooked up the PCM and turned the power, hit the pedal and I could hear the throttle body flap moving so I knew something was right. I turned the ignition and started right up and kept running. I...
Hi all,
Is the throttle body flap supposed to move when the ignition is in the ON position but not started? My flap seems like it wants to move when the gas peddle is pressed but barley budges, is this normal? There is also a high wine coming from somewhere on the engine when the ignition is in...
One More thing, when I try to start it, if I pump the peddle it will rev but I have to pump it a bunch of times to try to keep it going, kinda like pumping an old school carb engine to get the gas in, any thoughts??
Thanks for the replies!!
I checked the fuel pressure and it was around 55psi, I forgot to write down what it was and will have to borrow the pressure tester again. Thanks!
I am going back to the tuner to have him delete all the EVAP stuff do you think I should have him delete the "lost...
d_raabi, THANKS!! You cleared up the P0690 ECM / PCM power relay sense circuit high code. So now I only have the following codes
P0036 Heater control circuit bank 1 sensor2
P0056 Heater control circuit bank 2 sensor 2
P0443 EVAP emission system purge control valve circuit
P0449 EVAP emission...
I got to look over my harness tonight and I can't find anything wrong. For the Grounds I have:
One from the battery and the harness to the passenger head
One from the rear driver head
and one on the block on the drivers side with two ground wires to it
I got to looking at my power...
Thanks da-raabi, I was planning on going through all the wiring this weekend. I was just excited to use the code reader and was hoping it would cure the problem.... Guess I will have to cut the old exhaust and install the o2 sensors correctly somehow. Do I need to buy a nut or something like...
Ok, I hooked up the code reader and got 10 codes as listed:
P0036 Heater control circuit bank 1 sensor2
P0056 Heater control circuit bank 2 sensor 2
P0443 EVAP emission system purge control valve circuit
P0449 EVAP emission system vent valve solenoid circuit
P0452 EVAP emission system pressure...
Ok, I hooked up the code reader and got 10 codes as listed:
P0036 Heater control circuit bank 1 sensor2
P0056 Heater control circuit bank 2 sensor 2
P0443 EVAP emission system purge control valve circuit
P0449 EVAP emission system vent valve solenoid circuit
P0452 EVAP emission system pressure...