Recent content by Elliot W

  1. Elliot W

    LS 5.3 High Idle

    Have you used off-brand injectors before or used GM injectors only?
  2. Elliot W

    LS 5.3 High Idle

    Thanks guys. A coworker with HP tuners may be able to help me out with getting data before I head to the tuner in a week. One more thing I forgot to mention…it’s also doing what I think is called rpm hang. When I give it some gas in neutral, the rpm’s rise but take extra long to come back down...
  3. Elliot W

    LS 5.3 High Idle

    Thanks for the input. I'll see about moving the MAF further from the throttle body, but the wire on the harness is only so long. The knock sensors were Amazon specials. Did you get you knock sensors from the chevy dealership? No info on the motor's miles. Came with the C10 (in the bed) and was...
  4. Elliot W

    LS 5.3 High Idle

    I checked for vacuum leaks but attaching my air compressor to the brake booster line (5-10psi) with a latex glove over the intake at the MAF. The glove stays inflated for a long time when I turn off the air. Leaks were identified with soapy water. I'm confident there are no vacuum leaks (even...
  5. Elliot W

    LS 5.3 High Idle

    I'm having a high idle issue, seems to be a common problem (according to the internet) but I haven't seen anything posted in these threads with all of your expert assistance. Embarrassingly enough, I think this has been an issue since swapping the motor in and I just never really picked up on it...
  6. Elliot W

    What did you pay for a square

    This may be the best deal on here yet.
  7. Elliot W

    Wheel and tire size help!!

    @bluex a while back I did the axle flip kit as you recommended (and while we are on the topic of lowering), currently procrastinating grinding off the stock bump stops to install low profile ones. The stock stops are resting on the axle...is there any damage that could happen to the axle for...
  8. Elliot W

    Brake booster bolts

    Thanks guys. Just wanted to make sure I wasn’t missing something obvious before punching holes in the firewall. Put two holes in it today. Turned out pretty good I think.
  9. Elliot W

    Brake booster bolts

    Looking for advice on the upper bolts for the brake booster. The truck didn’t have a booster when I got it so I think that’s how it came stock. I can’t think of how to fasten the top of the brake booster to the truck. There’s just enough space to drop a thin nut behind the firewall bracket, no...
  10. Elliot W

    How is everyone making their wiring look not a mess under the hood.?

    Great advice Zach, I'm going to take your advice and reroute the fuel line that way. What fitting did you use to go fuel rail quick disconnect to AN line?
  11. Elliot W

    Vent window trick?

    I'm talking about gaps between the glass and gasket, along the bottom and the diagonal edges. I can get some photos of it tonight. The frame itself went back in the door no issues.
  12. Elliot W

    Vent window trick?

    Did you have any gaps after installing the gasket or is it just my workmanship?
  13. Elliot W

    Vent window trick?

    I used that trick...cut the inside of the gasket instead of taking the window out of the frame. Worked great! The nut and other hardware was pitted, like it would strip if I tried to back it out any more than I already had tried, so this trick saved me that headache. The kit I used was precision...
  14. Elliot W

    Plans for the summer.

    Almost forgot to suggest...bring a fire extinguisher too. Not so much for the fuel system as it is for an old electrical system.
  15. Elliot W

    Plans for the summer.

    Thanks for the add Chad. Just like Spencer said, most components can be picked up stock in local stores, and of course consumables (oil, coolant, etc.). Maybe run through the cooling system one last time, check hoses/clamps, see if rad needs replacing if its not keeping the temps down, and...
See more

Latest posts

Forum statistics

Threads
42,116
Posts
909,467
Members
33,611
Latest member
RNFL
Top