Recent content by Domer
-
TH 350 Torque Converter
Did you do this motor work while you were doing the swap? how high of a stall do you have on the converter? if you have a stock converter on that build, or a real tight low stall converter, then that would cause it to die when put into gear.- Domer
- Post #16
- Forum: Transmission & Transfer Case
-
oasis hp 1000 onboard air
Not even close man... Some specs on the Oasis HP1000: 17"Lx7"Wx10"H Wt.: 45 lbs Motor Type: Series wound Max Load Amps:200 @ 12vdc/ Max psi 200/ At Psi 100, CFM is 8 and draws Current of 180 amps. Hit up jeremy at TRE 5 Customs and get a couple of big Kintek Batteries and some very...- Domer
- Post #4
- Forum: Tech Discussion
-
oasis hp 1000 onboard air
Its a York engine driven compressor with a big ass electric motor.. they are nice if you don't have the room for an EDC. But that said, you need a hell of an electrical system to handle the draw of those motors. but they fill hella fast.. i loved my york i had on my truck setup as an EDC.- Domer
- Post #2
- Forum: Tech Discussion
-
1UZ-FE, Flamesuit donned
You will most likely have to have your bellhousing cut, and a toyota bellhousing welded on.. not sure if any adapters are availble. And then adapt a chevy flexplate. I have a friend that put one in a nissan hardbody, but that was with a manual trans though. They clean up well also if you don't...- Domer
- Post #2
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
What do you think about these steering wheels
Here is mine. I love the mahogany wheel, i have the wood strip on the passenger side, but its going away... -
What should I do now !!!!!
First off, please use some punctuation. That was really hard to read. and to answer what i think was your question, if you didn't have the radiator in and the trans lines were not hooked up and pumping fluid out, then you probably burnt up the trans and warranty doesn't cover that.- Domer
- Post #2
- Forum: Transmission & Transfer Case
-
350 stutters/shakes on upshift
I ended up taking it to a shop, and it was just wore out. needs new seals and bushings. but nothing broken. so $600 later i will have a good working th350 again..- Domer
- Post #4
- Forum: Automatic Transmission
-
Hello from San Diego CA
Welcome man.. I live out in el cajon about 3 miles from you... if you got any questions feel free to ask.. ill help out with what I can.- Domer
- Post #8
- Forum: Introduction
-
Newbie from SoCal
welcome from East San Diego.. Also Navy, Im stationed over on Coronado right now- Domer
- Post #9
- Forum: Introduction
-
Dynamat alternative
Go to sounddeadener.com and you can get fatmat for about the same price per sq. Ft... -
=Sunset= Member from San Diego
Thanks mr. Clean, I just moved from lakeside to el cajon..- Domer
- Post #17
- Forum: Introduction
-
350 stutters/shakes on upshift
I have a 77 C10 2wd, dont know if the trans is from that truck or not. it is a TH350, when im driving just normal and it goes to upshift to 3rd, it feels like a stutter/shake then it will shift, sometimes i have to back peddle to get it to shift. anything in particular to look for when i pull...- Domer
- Thread
- Replies: 3
- Forum: Automatic Transmission
-
=Sunset= Member from San Diego
I lived in IB for a few monnths.. never been to the plank...- Domer
- Post #15
- Forum: Introduction
-
=Sunset= Member from San Diego
Right now im at North Island Naval air station on Coronado.. looking at getting orders to LPD18 USS New Orleans, on 32nd st. Base.- Domer
- Post #13
- Forum: Introduction
-
=Sunset= Member from San Diego
Just passed 7 years and am getting ready to re enlist for another 6 years. Been on 2 ships, currently on shore duty and getting ready to go back to another ship soon. Thanks for you support.- Domer
- Post #11
- Forum: Introduction
