Recent content by devin bianco

  1. devin bianco

    no power to starter/wiring issues

    problem solved. bad ignition switch, also a ground strap to the motor fixed the other issues.
  2. devin bianco

    no power to starter/wiring issues

    Edit, problem #1 solved. i forgot a ground wire and when i hooked it up i have all my accessories. I still don't have power to starter though. my last question is, when should the small starter terminal (purple) be hot? during crank or ignition? i only have a large terminal with 1 wire coming...
  3. devin bianco

    no power to starter/wiring issues

    what wire is it exactly that i check? and how do you bypass neutral safety?
  4. devin bianco

    no power to starter/wiring issues

    ALSO.... if i turn my washers on high, my blower motor and blinker indicators turn on. wtf plz help
  5. devin bianco

    no power to starter/wiring issues

    also..... my blinker indicators come on (not flash) when i turn my wipers on. Also, my "brake" indicator light comes on when i turn key to "crank". is this normal or a WTF
  6. devin bianco

    no power to starter/wiring issues

    I need steps on how to troubleshoot no power to the starter soleiod. bare with me because i do not have the best technical vocabulary when it comes to this stuff. i have begun the process completely re-wiring my sbc with the original wiring harness, at this point in time all i want to do is get...
    • devin bianco
    • Thread
    • k10 neutral safety switch sbc sbc350 small block 350 starter starter ignition starter soleniod wiring wiring harness
    • Replies: 12
    • Forum: Engine & Performance
  7. devin bianco

    small block oil to rocker arm issues

    thanks for the responses guys
  8. devin bianco

    small block oil to rocker arm issues

    solution found, just keep running it with a drill and eventually it will come. spun it for 30+ minutes
  9. devin bianco

    small block oil to rocker arm issues

    my exhaust rocker on cylinder one is receiving no oil when the oil pump is getting turned over. its a brand new crate motor, im assuming the oil passage is blocked. what's the best way to clean that passageway? edit: i've tried plugging all other holes on drivers bank and running at 60 psi for...
  10. devin bianco

    Dana 44 overhaul...2 different spindles?????

    So long story short, i tore apart my 1979 k10 dana 44 front axle that was stock as far as i knew. ordered ball joints U joints and bearings. i got my ball joints in, U joints in but ran into an issue with the spindles. My driver and passenger spindles where noticeably different. the new bearings...
  11. devin bianco

    AXLE SHAFT HELP!!!!!

    i ended up finding a very helpful guy at advanced auto, apparently napa had me order driveshaft U joints not axle shaft. went through moog and vehicle fitment at advanced and seemed to work out fine.
  12. devin bianco

    AXLE SHAFT HELP!!!!!

    Doing U joints on my 1979 Chevy k10 pickup with a Dana44 spicer axle. Axle shafts came out fine but after I installed new U joints the bearing caps would not fit through the knuckle. The actual CV housings will fit without the U joints in, but after instal the bearing caps stick out to far to go...
  13. devin bianco

    Longbed Inspiration needed

    thats fair, por15 is a life saver that stuff works great. As long as the rocker and cab corners are still present, it will look 10x better than majority of squares in the midwest lol.
  14. devin bianco

    Longbed Inspiration needed

    fixing the rust while its still fairly solid is probably a good idea, especially considering aftermarket patch panels are not always very accurate, its nice to have reference points from oem sheet metal.
  15. devin bianco

    quick question, full time to locking hubs (k10 10 bolt)

    I am doing the 203 to 205 swap on my 79, soon enough the front axle is going to be rebuilt and i know i will need t install a manual locking hub kit (currently has no hub locking mechanism). when i look it up, all i see is part time 203 kits that include the hubs. In this case will i just need a...
See more

Latest posts

Forum statistics

Threads
42,109
Posts
909,247
Members
33,593
Latest member
shake1969
Top