Recent content by 85squaredC10

  1. 85squaredC10

    Carb to TBI Conversion

    Your very welcome. Good luck on your project. I can round up psrt numbers up you need them. Sent from my SM-G965U1 using Tapatalk
  2. 85squaredC10

    Carb to TBI Conversion

    I only have a single tank. On drivers side. I would think that as long as the line dimensions are the same, it should fit your application. Probably just reuse your current selector. But im not positive. Sent from my SM-G965U1 using Tapatalk
  3. 85squaredC10

    Carb to TBI Conversion

    I bought a new baffled tank....and in-tank fuel pump for a 1987 R10 with fuel injection. Used original gas lines for return style setup. In my case, I went with -6 lines mated to the 1/4" hard lines at the pump. And of course a fuel filter appropriate for the donor vehicle. For me it was a 93...
  4. 85squaredC10

    What have you done to your square lately??

    Sounds like I need a louder exhaust and a better stereo!!! Lmao Sent from my SM-G965U1 using Tapatalk
  5. 85squaredC10

    What have you done to your square lately??

    I am also looking into getting electric fans. Can't decide if I want one big fan or two smaller fans. Any thoughts? Sent from my SM-G965U1 using Tapatalk
  6. 85squaredC10

    New Member

    Welcome Sent from my SM-G965U1 using Tapatalk
  7. 85squaredC10

    What have you done to your square lately??

    Thanks for mentioning that. I'll have to check it out. Any advise for testing good/bad? Much appreciated. Side note: mine was new 2 years ago. Sent from my SM-G965U1 using Tapatalk
  8. 85squaredC10

    What have you done to your square lately??

    Mine sure is loud!! I couldn't imagine it being louder than it is!! Lol Sent from my SM-G965U1 using Tapatalk
  9. 85squaredC10

    What have you done to your square lately??

    So, why are they not equally spaced? Sent from my SM-G965U1 using Tapatalk
  10. 85squaredC10

    What have you done to your square lately??

    I was heating up my old rods to put on new pistons/pins....I ended up not being on center with this one. Is this going to cause an issue? If so, how do I get it off without damaging new parts? Sent from my SM-G965U1 using Tapatalk
  11. 85squaredC10

    What have you done to your square lately??

    Green thing has factory number stamped on it. Google it. My 85 has one. It is a speed sensor. Sent from my SM-G965U1 using Tapatalk
  12. 85squaredC10

    What have you done to your square lately??

    Looks like it may have been for a plow?. Pink wires running to the front look like heavy duty power wire. Sent from my SM-G965U1 using Tapatalk
  13. 85squaredC10

    What have you done to your square lately??

    Just replaced a coolant temp sensor today. Back to reading correctly! ......the little things! [emoji41] Sent from my SM-G965U1 using Tapatalk
  14. 85squaredC10

    What have you done to your square lately??

    Nice work!! I remember when I blew apart my harness for my 85 to 93 tbi swap. What a mistake!! I took 2 seasons to learn ALL the wiring diagrams and pinouts. It was a huge job, but I got it all done and it runs fantastic!! While I didnt want to take the time, nor did I want to learn wiring, I...
  15. 85squaredC10

    What have you done to your square lately??

    Dont forget to order the water pump!! .....its been a few days. [emoji16] Sent from my SM-G965U1 using Tapatalk
See more

Latest posts

Forum statistics

Threads
42,187
Posts
910,932
Members
33,681
Latest member
squareframe
Top