Recent content by 81squared

  1. 81squared

    Have a rollpan…. wants a bumper ….

    Thanks for the input .. I’m torn, don’t know if I want to go through the mods for this..
  2. 81squared

    Have a rollpan…. wants a bumper ….

    I have a 80 K10 I installed a nice roll pan, welded it in and painted the truck. Now I want a bumper FML Is there anyway to cut access holes in the roll pan and install a new stock GM rear bumper ?? or any bumper for that matter
  3. 81squared

    Painted driveshafts?

    bro whatever you do.... DO NOT paint that driveshaft !!!!
  4. 81squared

    Roll Pan / Bumper

    nope, no towing
  5. 81squared

    Roll Pan / Bumper

    Hello so after installing a nice roll pan, welded , filled and painted the truck. Now I want a bumper again ( Westin 21000) Can I just cut holes in the roll pan to accommodate the bumper brackets? Or will the roll pan interfere with the bumper footprint?
  6. 81squared

    Neutral safety switch questions

    This is my neutral safety switch. I think. Currently it has only 2 wires going to it. The tie into the harness on the steer column. It does not appear to be the correct gauge for the back up lights. I Just see a thinner blue and green wire. Is this even a neutral safety switch? Am I...
  7. 81squared

    Tail light help !!!

    thanks for the wiring diagram, I just ordered all new color correct wire Im going to re wire everything. everything makes sense now, hope it works when Im done !! thanks again
  8. 81squared

    Tail light help !!!

    I wanted to cut all that out and rewire the back wires. I don’t like the old crimp connectors and the green wire is breaking. Good info. Thanks
  9. 81squared

    Tail light help !!!

    Ok … so, before I started fixing up my wiring mess all my tail lights worked. Since then I started going through the wiring in the truck and there was 3 splices in the tail light harness, I decided to cut out almost all the wire goikg from the firewall harness to the plug in the back. I color...
  10. 81squared

    80 K10 headlight bezel question

    hello I have a 80 K10, I took the front trim off when I painted the truck. I cannot figure out how to install the clear rectangular lights under the head light. I have new lenses and existing OG metal housings. Unfortunately I did not photograph the break down process. I assume the metal...
  11. 81squared

    Fuel line questions

    Looking to cut my OE hard fuel line that goes from the fuel filter to the carb so I can run rubber hose to my edlebrock carb. Would a 3/8 fuel line slide over the existing hard line after I cut the flare off ? I assume 5/16 would be to tight ? I currently purchased a 3/8 fuel filter and a...
  12. 81squared

    Auto shift linkage

    Thanks for the input. I ordered them.
  13. 81squared

    Auto shift linkage

    A couple things … Where can I find this bushing ? Do I need to buy rhe whole bracket to get one. Any part numbers or links would be appreciated Do I need to replace that rusty spring ? Does that hold the bushing in ? Any help would be appreciated Thanks
  14. 81squared

    Question about transmission

    thanks very much, no rush, Im a month from crossing that bridge but yes, thanks for your help !! happy Labor Day !
  15. 81squared

    Question about transmission

    I really dont have any relevant pics yet, carb is in the box, motor is being built. I just never had a auto so its a little confusing, Im glad to hear you have a TH350 and a eddy and the kick down works, im sure it will, i would just rather learn of any issues before hand, Im new to this aspect...
See more

Latest posts

Forum statistics

Threads
42,128
Posts
909,766
Members
33,622
Latest member
timk
Top