Search results
-
Sealing intake manifold?
R72232 is the John Deere part number, shows the balls themselves start off at .32 In. I can't remember off hand what they crush down though.- aasleson
- Post #21
- Forum: Engine & Performance
-
Sealing intake manifold?
We use lead balls for figuring out shim packs for final drive preload on john deere tractors. If you have a deere dealer close I could find a part number for you.- aasleson
- Post #19
- Forum: Engine & Performance
-
Gone & done it again!
Beautiful CUCV! My ill advised way of getting old diesels started is taking a cloth rag and putting some gas on it and holding it over the intake with the air cleaner off. Much more efficient then ether bunny- aasleson
- Post #2
- Forum: Diesel 6.2, Conversions Cummins, etc.
-
What have you done to your square lately??
Yupp, and all of the junk i normally rob parts off of have 52's or 63's -
What have you done to your square lately??
Started doing my ORD 2 inch shackle flip on the CUCV to get rid of the lift blocks last night passenger side went well got the driver side apart and found the main leaf broke. -
What have you done to your square lately??
He does, he loves going for rides. It'll be his pickup when hes old enough. -
What have you done to your square lately??
Finally found a set of 31x10.5x15's and even came with a decent set of rims, we'll see how the paint holds up but they were $600 and the tires are pretty much new. Got them installed today along with the new tail light lenses -
Fuel tank replacement on 1987 LS swapped square body
Is he sure its an issue with the tank and just not a fuel line leaking at the sending unit?- aasleson
- Post #6
- Forum: Tech Discussion
-
Fuel tank replacement on 1987 LS swapped square body
Welcome! The parts required depend on how your Fuel system is set up, most common is to use the 87 Fuel tank and run an ls Fuel pump in the tank. Beings as yours is an 87 I'd assume they reused the factory tank. In my opinion for the pumps and tank selector if there is no issue with it I would...- aasleson
- Post #2
- Forum: Tech Discussion
-
What have you done to your square lately??
Got tail lights, bumper and bed pulled off the CUCV and got the service bed pulled around to start taking measurements for making the mounts and possibly relocating fuel tank to a blazer tank. -
What new tools have you got lately?
The price changes wildly on it for some reason, when I first found it they had it listed at 600 and it randomly went on sale for 499 and I slowly went up after that. I set a notification for if it dropped under 500. They had 2 left when I ordered it at 425. -
What new tools have you got lately?
I've been watching this gearwrench 209 piece socket set for a long time and they dropped it to $425 for a day, so I ordered it. Now all of my miscellaneous socket sets can come home with me and these will be my new work sockets https://a.co/d/04AOAzZk -
What have you done to your square lately??
Pulled the rest of the decent parts off the C30 and brought it in for scrap. Then used the funds to buy bucket seats from a 2014 ram and a center console from a 2013 silverado to replace the bench in the suburban. -
What have you done to your square lately??
Got the plow mount pulled off and the CUCV bumper and guard back on, need to fix an exhaust leak and get the bed pulled to make way for the service bed that will take its place. -
What have you done to your square lately??
Thank you for the info! I will do that, I was going to pull the speedo from the burb and the temp gauge from the c30 that my 454 came from -
What have you done to your square lately??
Went looking for tail lights for the K10 in our junkyard, struck out on that but did come across a distributor and a factory tach cluster out of a C65 with a blown big block. Looks like the oil pump drive shaft broke where it meets the pump. Pieced together one good distributor from the two... -
TV & Throttle bracket with 1406 carb
https://a.co/d/0c5BR8a6 This is the bracket I used for my 700r4 1406 combo.- aasleson
- Post #4
- Forum: Engine & Performance
-
What have you done to your square lately??
Finished the tailpipe and rear hanger, only to find the exhaust manifold is leaking on cylinder 1. -
What have you done to your square lately??
Finished my exhaust. Debating weather I want a turn down at the rear to get it under the reciever hitch or aim the turn down out and down and cut the pipe after the shackle -
What have you done to your square lately??
I was curious why it was flagged for approval too -
What have you done to your square lately??
Started redoing exhaust in the suburban -
What have you done to your square lately??
Finished buffing and did a finish wash to get the oversprayed buffing compound off. -
What have you done to your square lately??
Finally started doing the gratifying job of buffing Kai's K10 -
What have you done to your square lately??
Started to dig out vehicles from the foot of snow that got dumped on us
