Search results

  1. S

    Need AC help!

    New ac/blower switch seems to have corrected the issue.
  2. S

    Need AC help!

    85 stock set up minute emissions. New compressor, new lines, new low pressure switch, no leaks. Compressor is kicking in and out with controls turned to off. Acts like a wiring issue but all stock wires in good condition. Thoughts? Was some emissions piece removed that could be causing this...
  3. S

    AC Questions

    Got the vacuum issue resolved. Have air at vents now although switching to defrost still doesn’t seem to force all the air to those vents. Still having the compressor kick on after all controls are turned to off.
  4. S

    AC Questions

    85 c10 original system converted to 134a. Just had it vacuumed down and charged. New compressor, evaporator etc. blows cold but only out of heater vent. Where to start on the vacuum lines for that? Also, I have noticed even with the controls set to off the compressor will cycle. Is that normal...
  5. S

    Before and After

    I ordered it from Rock Auto. Surprised how nice it was and how well it fit. Professional Grade...
  6. S

    LMC Dash Pad Supplier

    Fit is ok. I have some waves in the top. It sits high near the VIN and sags a little at the center speaker then goes back up toward the right pillar. If I was building a show truck it would not work.
  7. S

    LMC Dash Pad Supplier

    My LMC dash said dashes direct on the box. That was about two months ago.
  8. S

    Before and After

    THAT'S IT???????....only 2 pics??........more pics..............you're what we used to call some girls in high school........... A PR!CK TEASER!!!!! Ha! What do you want to see...?
  9. S

    Before and After

    Well, of course it has taken some money to do this one. The goal was to build it for less than 6k including the price of the truck. I'm going to be closer to $7,500 when its done, but way cheaper than my 71.
  10. S

    Before and After

    Been working on this 85 for a year now. Started out as a 2500. Swapped body and drivetrain over to a SWB 1500 frame. Just need a vision and it comes together.
  11. S

    What goes here?

    It used to be a 3/4 ton...I swapped the whole thing over to a 1/2 ton SWB frame. Any ideas how best to plug it off?
  12. S

    What goes here?

    85 breather on a 350. When I got the truck this was not hooked up. Not sure where it originally ran and am having no luck with "The Google" ;) I'm sure it is emissions related, but need to figure out how to cap it off or something. Thanks,
  13. S

    Front body/radiator mounts RELOCATE?

    Yes it will make a difference. I just swapped an 85 long bed body over to a swb 79 frame. I used the 85 core support brackets and found out that I had to redrill the holes for the brackets to get it all to line up. I would recommend getting your front clip on and somewhat adjusted and then mark...
  14. S

    1987 GMC High Serria K20

    I have a set of High Sierra badges off a 2500.
  15. S

    Another Oil Pressure Question

    I verified all ground straps, but don't remember there being one from firewall to frame. I have one from cab to frame but it was located toward rear of cab on right side. Thanks
  16. S

    Another Oil Pressure Question

    I read through the threads and didn't see this issue. 85 with 350. Have the dual oil pressure sensors. I swapped the motor/trans/body from a 2500 frame to a SWB 1500 frame. Oil pressure gauge worked prior. We fired up the motor after the swap and the gauge is all over the place. It jumps from...
  17. S

    I need a donut

  18. S

    I need a donut

    Here is what my exhaust manifold looks like. 2.5” inside diameter. The Mahle you mentioned might work
  19. S

    I need a donut

    OK, hoping to get some additional help. 1985 GMC C2500 with 350 and stock true dual exhaust in 2.5". All original. Cannot find the correct donut gaskets for the exhaust. Any help is appreciated.
  20. S

    I need a donut

    Recommended donuts did not fit. Back to the drawing board.
  21. S

    I need a donut

    I found the donuts at Advance. I will try them tonight and see if they work.
  22. S

    I need a donut

    Local O'Reilly's shows you can't even order the Fel Pro 8194...so, I will find it on-line and give it a try. Thank you.
  23. S

    I need a donut

    I have a 1985 350/400 out of a 2500 GMC. Running the stock exhaust manifolds with the A.I.R deleted. Also using the stock down pipes as the ole 2500 came factory with true duals. Like a dummy, I pitched the old donut exhaust gaskets on tear down and now I have no idea what size I need to put it...
  24. S

    Scottsdale interior door panel trim.

    I ended up swapping the the aluminum ones in the dash and doors because I couldn't find the re-pop black inserts for the doors.
  25. S

    Seat recovering

    I'm about to do this project this weekend. I went to my upholstery shop and got a piece of foam. Now it sounds like I better find a better pair of hog ring pliers. I like the trash bag tip...

Latest posts

Forum statistics

Threads
45,575
Posts
986,742
Members
38,666
Latest member
alwaysbroken
Top